Related Manuals for Advantech AIMB-262
Summary of Contents for Advantech AIMB-262
- Page 1 User Manual AIMB-262 Intel® LGA775 Core 2 Duo Mini ITX Motherboard with DDR2/ LAN/4COM/PCIe x16...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
-
Page 4: Declaration Of Conformity
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions. AIMB-262 User Manual... - Page 5 (32x16) DDR2 SODIM ELPIDA E5108AGBG-6E-E (RoHS)" M DDR2 (64x8) DDR2 SODIM ELPIDA E5108AGBG-6E-E M DDR2 (64x8) Transcend DDR2 SODIM TS128MS HYNIX HY5PS12821E-FP-S5 (RoHS)" M DDR2 Q64V8J (64x8) DDR2 SODIM ELPIDA TWN E5108AHSE- (RoHS) M DDR2 8E-E (64x8) AIMB-262 User Manual...
-
Page 6: Ordering Information
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. - Page 7 It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the AIMB-262, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
- Page 8 AIMB-262 User Manual viii...
-
Page 9: Table Of Contents
Board layout: Jumper and Connector Locations ........5 Figure 1.1 Jumper and Connector Location ........ 5 Figure 1.2 I/O Connectors ............5 AIMB-262 Block Diagram................6 Figure 1.3 AIMB-262 Block Diagram ........... 6 Safety Precautions ..................7 Jumper Settings ..................8 1.8.1 How to set jumpers ............... - Page 10 Example Program ............... 57 Appendix B I/O Pin Assignments ......61 Parallel Port (LPT1) ................62 Table B.1: Parallel Port (LPT1)..........62 USB Header (USB56) ................62 Table B.2: USB Header (USB56) ..........62 VGA Connector (VGA1)................63 AIMB-262 User Manual...
- Page 11 Table B.22:System I/O Ports ............70 B.20 DMA Channel Assignments ..............71 Table B.23:DMA Channel Assignments........71 B.21 Interrupt Assignments ................71 Table B.24:Interrupt Assignments..........71 B.22 1st MB Memory Map ................72 Table B.25:1st MB Memory Map ..........72 AIMB-262 User Manual...
- Page 12 AIMB-262 User Manual...
-
Page 13: Chapter 1 General Information
Chapter General Information... -
Page 14: Introduction
VGA performance and shares system memory up to 224 MB. Advantech AIMB-262 is designed with Intel 945GC chipset and supports Intel Core 2 Duo processor up to FSB 800 MHz. A rich I/O connectivity of 4 serial ports, 6 USB 2.0, single GbE LAN and 2 SATA ports. -
Page 15: Specifications
Storage temperature: -20 ~ 70° C (-4 ~ 158° F) Humidity: 5 ~ 95% non-condensing Power supply voltage: +3.3 V, +5 V, +12 V, -12 V, 5 Vsb Power consumption: Board size: 170 mm x 170 mm (6.69" x 6.69") Board weight: 0.365 kg AIMB-262 User Manual... -
Page 16: Jumpers And Connectors
Jumpers and Connectors Connectors on the AIMB-262 motherboard link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application. The tables below list the function of each of the board jumpers and connectors. Later sections in this chapter give instructions on setting jumpers. -
Page 17: Board Layout: Jumper And Connector Locations
Audio1 LAN_USB12 USB34 VGA1 COM12 KBMS1 JSETCOM2 TPM_SLOT1 ATX12 V LPT1 JFP2_1 CPU_FAN1 SATA2 SATA1 PCIEX16 CMOS1 PSON1 CHA_FAN1 COM3 COM4 DIMM1 USB56 SPI BIOS SPI_CN1 EATXPWR1 Figure 1.1 Jumper and Connector Location Figure 1.2 I/O Connectors AIMB-262 User Manual... -
Page 18: Aimb-262 Block Diagram
AIMB-262 Block Diagram Figure 1.3 AIMB-262 Block Diagram AIMB-262 User Manual... -
Page 19: Safety Precautions
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer’s instructions. AIMB-262 User Manual... -
Page 20: Jumper Settings
1.8.2 CMOS clear (CMOS1) The AIMB-262 motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set J1 to 2-3 closed for just a few sec- onds, and then move the jumper back to 1-2 closed. -
Page 21: Com2 Rs 232/422/485 Mode Selector (Jsetcom2)
Jumper Setting *RS232 (5-6) + (7-9) + (8-10) + (13-15) + (14-16) closed RS422 (3-4) + (9-11) + (10-12) + (15-17) + (16-18) closed RS-485 (1-2) + (9-11) + (10-12) + (15-17) + (16-18) closed *: Default AIMB-262 User Manual... -
Page 22: System Memory
The built-in second-level cache in the processor yields much higher performance than conventional external cache memories. 1.12 Processor Installation The AIMB-262 is designed for LGA775, Intel Pentium 4, Intel Core 2 Duo, Celeron D and Intel Pentium dual core D processor. AIMB-262 User Manual... -
Page 23: Chapter 2 Connecting Peripherals
Chapter Connecting Peripherals... -
Page 24: Introduction
The parallel port is normally used to connect the motherboard to a printer. The AIMB- 262 includes an onboard parallel port, accessed through a 25-pin flat-cable connec- tor, LPT1. Note! Parallel cable is not enclosed in the box as standard accessory. The order part number is 1700008809. AIMB-262 User Manual... -
Page 25: Usb Ports (Lan1_Usb12/Usb34/Usb56)
USB Ports (LAN1_USB12/USB34/USB56) The AIMB-262 provides up to six ports of USB (Universal Serial Bus). The USB inter- face complies with USB Specification Rev. 2.0 supporting transmission rate up to 480 Mbps and is fuse protected. The USB interface can be disabled in the system BIOS setup. -
Page 26: Vga Connector (Vga1)
VGA Connector (VGA1) VGA1 The AIMB-262 includes a VGA interface that can drive conventional CRT displays. VGA1 is a standard 15-pin D-SUB connector commonly used for VGA. Pin assign- ments for CRT connector VGA1 are detailed in Appendix B. AIMB-262 User Manual... -
Page 27: Serial Ports (Com1~Com4)
COM1/COM2 COM3/COM4 AIMB-262 supports four serial ports. 1 of RS-232/422/485 - COM2, COM1, COM3 and COM4. The user can use JSETCOM2 to select among RS 232/422/485 modes for COM2. These ports can connect to serial devices, such as a mouse or a printer, or to a communications network. -
Page 28: Ps/2 Keyboard And Mouse Connector (Kbms1)
PS/2 Keyboard and Mouse Connector (KBMS1) KBMS1 Two 6-pin mini-DIN connectors (KBMS1) on the motherboard provide connection to a PS/2 keyboard and a PS/2 mouse, respectively. AIMB-262 User Manual... -
Page 29: Cpu Fan Connector (Cpu_Fan1)
CPU Fan Connector (CPU_FAN1) CPU_FAN1 If fan is used, this connector supports cooling fans of 500 mA (6 W) or less. AIMB-262 User Manual... -
Page 30: System Fan Connector (Cha_Fan1)
System FAN Connector (CHA_FAN1) CHA_FAN1 If fan is used, this connector supports cooling fans of 500 mA (6 W) or less. AIMB-262 User Manual... -
Page 31: Front Panel Connectors (Jfp2_1)
Front Panel Connectors (JFP2_1) There are several external switches to monitor and control the AIMB-262. JFP2_1 5 and 7 Reset switch 1 and 3 Hard driver activity LED 2 and 4 Power/Sleep/Waiting LED 6 and 8 Power switch 2.9.1 Power/Sleep Waiting LED (JFP2_1) JFP2_1 pins 2 &... -
Page 32: Reset Connector (Jfp2_1 Pins 5 & 7)
JFP1 pins 1&2. This connection enables you to turn your computer on and off. 2.10 Line In, Line Out, Mic In Connector (AUDIO1) Line In Line Out Mic In AUDIO1 AIMB-262 User Manual... -
Page 33: Serial Ata Interface (Sata1, Sata2)
2.11 Serial ATA Interface (SATA1, SATA2) SATA1, SATA2 AIMB-262 features a high performance serial ATA interface (up to 300 MB/s) which eases cabling to hard drives with thin and long cables. AIMB-262 User Manual... -
Page 34: Pcie X 16 Slot (Pcie X 16)
2.12 PCIe x 16 slot (PCIE X 16) The AIMB-262 provides 1 PCIe x 16 slot. AIMB-262 User Manual... -
Page 35: Auxiliary 4-Pin Power Connector (Atx)
To ensure the enough power is supplied to the motherboard, one auxiliary 4 pin power connector is available on the AIMB-262. ATX must be used to provide suffi- cient 12 V power to ensure the stable operation of the system. -
Page 36: Tpm Connector (20-1 Pin Tpm_Slot)
This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. The order part number of TPM module is 9680004525. AIMB-262 User Manual... -
Page 37: Spi Flash Connector(Spi_Cn1)
2.15 SPI Flash connector(SPI_CN1) SPI flash card pin header which can flash BIOS while AIMB-262 can not be power on and ensures platform integrity. AIMB-262 User Manual... - Page 38 AIMB-262 User Manual...
-
Page 39: Bios Operation
Chapter BIOS Operation... -
Page 40: Introduction
CPUs from 386 through Pentium and AMD Geode, K7 and K8 (including multiple pro- cessor platforms), and VIA Eden C3 and C7 CPU. You can use Advantech’s utilities to select and install features to suit your designs for customers need. -
Page 41: Main Menu
Set Password Establish, change or disable password. Save & Exit Setup Save CMOS value settings to CMOS and exit BIOS setup. Exit Without Saving Abandon all CMOS value changes and exit BIOS setup. AIMB-262 User Manual... -
Page 42: Standard Cmos Features
Extended Memory The POST of the BIOS will determine the amount of extended memory (above 1 MB in CPU’s memory address map) installed in the system. Total Memory This item displays the total system memory size. AIMB-262 User Manual... -
Page 43: Advanced Bios Features
Eight settings are 6, 8, 10, 12, 15, 20, 24 and 30. – Typematic Delay (Msec) This item sets the time interval for displaying the first and second characters. Four delay rate options are 250, 500, 750 and 1000. AIMB-262 User Manual... -
Page 44: Advanced Chipset Features
This item enables users to set the DRAM RAS# precharge timing, system default is setting to “Auto” to reference the data from SPD ROM. Prechage delay (tRAS) [Auto] This item allows user to adjust memory precharge time. AIMB-262 User Manual... - Page 45 (DVMT). BIOS provides three options to choose (DVMT,FIXED and Both). DVMT/FIXED Memory Size [128MB] This item allows the user to adjust DVMT/FIXED graphics memory size. Init Display First This item is setting for start up Video output from PCI Express or Onboard device. AIMB-262 User Manual...
-
Page 46: Integrated Peripherals
This item enables users to set the OnChip IDE device status, including some of new chipsets also support for SATA device (Serial-ATA). Onboard Device This item enables users to set the Onboard device status, includes enable USB, AC97 and LAN devices. AIMB-262 User Manual... - Page 47 This item allows you to determine the active level of the RxD and TxD serial lines. The choices: “Hi, Hi”, “Lo, Lo”, “Lo, H”, and “Hi, Lo”. IR Transmission Delay This item allows you to enable/disable IR transmission delay. The options are “Enabled” and “Disabled”. AIMB-262 User Manual...
-
Page 48: Security Chip Configuration
Select an item and then press <Enabled> to display the configuration options. Note! To enable the TPM function, set the TPM Support item to [Enabled] and then save the change , After rebooting, the TPM Configuration menu will change into the following one. AIMB-262 User Manual... -
Page 49: Power Management Setup
PC and system devices for improving the power man- agement. ACPI Suspend Type [S3(STR)] This item allows user to select sleep state when suspend. S1(POS) The suspend mode is equivalent to a software power down; AIMB-262 User Manual... - Page 50 Primary IDE 0 (1) and Secondary IDE 0 (1) [Disabled] When Enabled, the system will resume from suspend mode if Primary IDE 0 (1) or Secondary IDE 0 (1) becomes active. The choices are “Enabled” and “Dis- abled”. FDD, COM, LPT PORT [Disabled] AIMB-262 User Manual...
-
Page 51: Pnp/Pci Configurations
PCI / VGA Palette Snoop [Disabled] This is set to “Disabled” by default. Maximum Payload Size [128] This item shows you the maximum TLP payload size for PCI Express devices. The option is setting to [128 bytes] by chipset specification. AIMB-262 User Manual... -
Page 52: Pc Health Status
VCORE and Other Voltages This shows the voltage of VCORE, +3.3 V, +5 V, +12 V, -12 V, VBAT(V), and 5 VSB (V). 3.2.11 Frequency/Voltage Control Spread Spectrum [Disabled] This item enables users to set the spread spectrum modulation. AIMB-262 User Manual... -
Page 53: Load Setup Defaults
Load Setup Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusable). These defaults will load automatically when you turn AIMB-262 Series system on. 3.2.13... - Page 54 Select Set Password again, and at the “Enter Password” prompt, please don’t enter anything; just press <Enter>. At the ”Confirm Password” prompt, again, don’t type in anything; just press <Enter>. Select Save to CMOS and EXIT, type <Y>, then <Enter>. AIMB-262 User Manual...
-
Page 55: Save & Exit Setup
Type “Y” will quit the BIOS Setup Utility and save user setup value to CMOS. Type “N” will return to BIOS Setup Utility. 3.2.15 Quit without Saving Note! Type “Y” will quit the BIOS Setup Utility without saving to CMOS. Type “N” will return to BIOS Setup Utility. AIMB-262 User Manual... - Page 56 AIMB-262 User Manual...
-
Page 57: Chipset Software Installation Utility
Chapter Chipset Software Installation Utility... -
Page 58: Before You Begin
To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the AIMB-262 are located on the software installation CD. The driver in the folder of the driver CD will guide and link you to the utilities and drivers under a Windows system. -
Page 59: Windows Xp Driver Setup
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Move the mouse cursor over the folder "INF". In INF folder, you can click "setup.exe" to complete the implement of the driver. AIMB-262 User Manual... - Page 60 AIMB-262 User Manual...
-
Page 61: Vga Setup
Chapter VGA Setup... -
Page 62: Introduction
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Move the mouse cursor over the folder "VGA". In VGA folder, you can click "setup.exe" to complete the implement of the driver based on Vista,Windows XP and Windows 2000. AIMB-262 User Manual... -
Page 63: Lan Configuration
Chapter LAN Configuration... -
Page 64: Introduction
Introduction The AIMB-262 has a single/dual Gigabit Ethernet LAN via dedicated PCI Express x 1 bus (Realtek RTL8111C), which offers bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000 Mbps. -
Page 65: Appendix A Programming The Watchdog Timer
Appendix Programming the Watchdog Timer... -
Page 66: Programming The Watchdog Timer
Programming the Watchdog Timer The AIMB-262's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it. - Page 67 Unlock W83627DHG Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock W83627DHG AIMB-262 User Manual...
-
Page 68: Table A.1: Watchdog Timer Registers
Bit 5: Write 1 to generate a timeout signal immedi- ately and automatically return to 0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. AA (hex) ----- Write this address to I/O port 2E (hex) to lock the watchdog timer 2. AIMB-262 User Manual... -
Page 69: Example Program
Inc dx Mov al,10 Out dx,al ;----------------------------------------------------------- Dec dx ; Lock W83627HG Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock W83627HG Mov al,87h Out dx,al Out dx,al AIMB-262 User Manual... - Page 70 Enable watchdog timer to be reset by mouse ;----------------------------------------------------------- Mov dx,2eh ; Unlock W83627HG Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- AIMB-262 User Manual...
- Page 71 Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al AIMB-262 User Manual...
- Page 72 Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; Lock W83627HG Mov al,0aah Out dx,al AIMB-262 User Manual...
-
Page 73: Appendix B I/O Pin Assignments
Appendix I/O Pin Assignments... -
Page 74: Parallel Port (Lpt1)
Parallel Port (LPT1) Table B.1: Parallel Port (LPT1) Signal Signal STROBE* AUTOFD* INIT* SLCTINI* ACK* BUSY SLCT * Low activity USB Header (USB56) Table B.2: USB Header (USB56) Signal Signal USB0_VCC5 USB1_VCC5 USB0_D- USB1_D- USB0_D+ USB1_D+ AIMB-262 User Manual... -
Page 75: Vga Connector (Vga1)
VGA Connector (VGA1) Table B.3: VGA Connector (VGA1) Signal Signal CRT_VCCIN VGA_G VGA_B V_SDAT H-SYNC V-SYNC V_SCLK RS-232 Interface Table B.4: RS-232 Interface (COM1~COM4) Signal AIMB-262 User Manual... -
Page 76: Rs-232/422/485 Setting Interface (Jetcom2)
RXD485_1 R_SINA RXD422_1 R_SINA RXD232_1 DCDA SOUTA COM1_DCD# COM1_SOUT COM1_TXD485N COM1_RXD485P SINA DTRA COM1_SIN COM1_DTR# COM1_TXD485P COM1_RXD485N SPI_CN1: SPI fresh card pin connector Table B.6: SPI_CN1:SPI fresh card pin connector Signal Signal +F1_3V F1_SPI_CS#_Q F1_SPI_CLK_Q F1_SPI_MISO_Q F1_SPI_MOSI_Q AIMB-262 User Manual... -
Page 77: Ps/2 Keyboard And Mouse Connector (Kbms1)
PS/2 Keyboard and Mouse Connector (KBMS1) Table B.7: PS/2 Keyboard and Mouse Connector (KBMS1) Signal KB DATA KB VCC KB CLK M_DATA M_VCC M_CLK CPU Fan Power Connector (CPU_FAN1) Table B.8: CPU Fan Power Connector (CPU_FAN1) Signal +12 V DETECT AIMB-262 User Manual... -
Page 78: System Fan Power Connector (Cha_Fan1)
System Fan Power Connector (CHA_FAN1) Table B.9: System Fan Power Connector (SYSFAN1/SYSFAN2) Signal +12 V DETECT B.10 Front Panel Connectors (JFP2_1) B.10.1Power/Sleep LED (JFP2_1) Table B.10: Power/Sleep LED (JFP2_1) Signal LED power (+5 V) LED power (+5 V) AIMB-262 User Manual... -
Page 79: Reset Connector (Jfp2_1)
B.10.4ATX Soft Power Switch (JFP2_1) Table B.13: ATX Soft Power Switch (JFP2_1) Signal 5 VSB PWR-BTN B.11 ATX1 12 V Auxiliary Power Connector (ATX1) Table B.14: ATX1 12 V Auxiliary Power Connector (ATX1) Signal +12 V +12 V AIMB-262 User Manual... -
Page 80: Atx Power Connector (Eatxpwr1)
12 V 12 V 3.3 V 3.3 V -12 V PSON -5 V B.13 USB/LAN ports (LAN1_USB12/USB34) Table B.16: USB Port Signal Signal Data0+ Data0- Table B.17: Ethernet 10/100Base-T RJ-45 Port Signal Signal XMT+ XMT- RCV- RCV+ AIMB-262 User Manual... -
Page 81: Line In, Line Out, Mic In Connector (Audio1)
SATA_0TX- SATA_0RX- SATA_0RX+ B.16 Serial ATA1 (SATA2) Table B.19: Serial ATA1 (SATA2) Signal Signal SATA_1TX+ SATA_1TX- SATA_1RX- SATA_1RX+ B.17 AT/ATX Mode (PSON1) Table B.20: AT/ATX Mode (PSON1) Signal Signal #PSON_SIO #PSON (to super IO) (to power supply) AIMB-262 User Manual... -
Page 82: Tpm_Slot1: Tpm Module Connector
Prototype card 360-36F Reserved 378-37F Parallel printer port 1 (LPT2) 380-38F SDLC, bisynchronous 2 3A0-3AF Bisynchronous 1 3B0-3BF Monochrome display and printer adapter (LPT1) 3C0-3CF Reserved 3D0-3DF Color/graphics monitor adapter 3F0-3F7 Diskette controller 3F8-3FF Serial port 1 AIMB-262 User Manual... -
Page 83: Dma Channel Assignments
IRQ12 PS/2 mouse IRQ13 INT from co-processor IRQ14 Primary IDE Channel IRQ15 Secondary IDE Channel IRQ3 Serial communication port 2 IRQ4 Serial communication port 1 IRQ5 Available IRQ6 Diskette controller (FDC) IRQ7 Parallel port 1 (print port) AIMB-262 User Manual... -
Page 84: 1St Mb Memory Map
1st MB Memory Map Table B.25: 1st MB Memory Map Addr. range (Hex) Device E0000h - FFFFFh BIOS CC000h - DFFFFh Unused C0000h - CBFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFFFh Base memory AIMB-262 User Manual... - Page 85 AIMB-262 User Manual...
- Page 86 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2008...
Need help?
Do you have a question about the AIMB-262 and is the answer not in the manual?
Questions and answers