Yamaha F30A Service Manual page 278

Index
Friction plate (H model)...............................7-8
Fuel hose, blowby hose,
and cooling water hose .............................4-1
Fuel pump, fuel filter, and fuel joint .............4-2
Fuel system..............................2-10
G.
General .....................................................3-15
General specification ..................................2-1
General torque ..........................................2-29
Good working practice ................................1-5
H.
Hose routing................................................4-1
How to use this manual...............................1-1
Hydraulic tilt unit and PTT unit ..................7-25
I.
Identification................................................1-6
Ignition and ignition control system...........8-15
Ignition coil, CDI unit,
and Rectifier Regulator ...........................5-16
Installing the carburetor ............................4-15
Installing the clamp bracket ......................7-29
Installing the cylinder head .......................5-39
Installing the hydraulic tilt unit ...................7-30
Installing the lower unit .............................6-19
Installing the power unit ............................5-52
Installing the propeller
shaft housing assembly ..........................6-17
Installing the PTT unit ...............................7-31
Installing the shift rod,
oil seal housing, and drive shaft..............6-17
Installing the sprocket and timing belt.......5-24
Installing the starter motor ........................8-13
Installing the steering arm.........................7-23
Installing the tiller handle ............................7-6
Installing the upper case ...........................7-23
Installing the water pump ..........................6-18
L.
Lower unit ...................... 2-11
Lubricating the outboard motor .................3-17
M.
Maintenance interval chart..........................3-1
Maintenance specification...........................2-7
Manual format .............................................1-1
Manual starter (M and W model) ................5-7
Measuring the forward
and reverse gear backlash......................6-26
i-3
, ,
2-17 3-3
, , ,
2-18 3-13 6-1
Measuring the peak voltage ....................... 8-7
Model.......................................................... 1-6
P.
Part, lubricant, and sealant......................... 1-4
Port view..................................................... 8-3
Power unit........................ 2-7
Power unit (check and adjustment) ............ 5-1
Power unit assembly ................................ 5-13
Precaution when transporting
or storing the outboard motor ................. 1-20
Predelivery check ..................................... 1-14
Propeller selection .................................... 1-13
Propeller shaft housing............................... 6-6
Propeller size............................................ 1-13
PTT cylinder ............................................. 7-46
PTT electrical system ............................... 7-52
PTT gear pump......................................... 7-39
PTT motor................................................. 7-34
R.
Refacing the valve seat ............................ 5-33
Removing the carburetor .......................... 4-12
Removing the clamp bracket .................... 7-29
Removing the cylinder head ..................... 5-29
Removing the drive shaft,
oil seal housing, and shift rod ................. 6-13
Removing the hydraulic tilt unit................. 7-28
Removing the lower unit ............................. 6-4
Removing the power unit.......................... 5-20
Removing the propeller
shaft housing assembly ............................ 6-7
Removing the PTT unit............................. 7-28
Removing the starter motor ........................ 8-9
Removing the steering arm ...................... 7-22
Removing the tiller handle .......................... 7-6
Removing the timing belt and sprocket .... 5-23
Removing the upper case......................... 7-19
Removing the water pump.......................... 6-5
Replacing the oil filter ................................. 3-5
Replacing the timing belt ............................ 5-3
Replacing the valve guide ........................ 5-31
S.
Safety while working................................... 1-4
Sealant and locking agent table ................. 1-3
Selecting the connecting rod bearing ....... 5-47
Selecting the crankshaft main bearing ..... 5-49
Selecting the forward gear shim ............... 6-23
Selecting the pinion shim.......................... 6-22
Selecting the reverse gear shim ............... 6-24
Selection................................................... 1-13
, , ,
2-14 3-4 5-13
67C3K11