Yamaha F30C Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Outboard Motor
  5. F30C
  6. Owner's manual
Yamaha F30C Owner's Manual

Yamaha F30C Owner's Manual

Outboard motor f30c; f40c
Hide thumbs
Table of Contents

Advertisement

Quick Links

F30C
F40C
OWNER'S MANUAL
U.S.A.Edition
LIT-18626-05-48

Advertisement

Table of Contents
loading

Related Manuals for Yamaha F30C

Summary of Contents for Yamaha F30C

  • Page 1 F30C F40C OWNER’S MANUAL U.S.A.Edition LIT-18626-05-48...
  • Page 3 NOTE: Yamaha. If you have any question about the A NOTE provides key information to make operation or maintenance of your outboard procedures easier or clearer.

  • Page 4: Table Of Contents

    EMU00003 CONTENTS GENERAL INFORMATION BASIC COMPONENTS OPERATION MAINTENANCE TROUBLE RECOVERY INDEX READ THIS OWNER’S MANUAL CAREFULLY BEFORE OPERATING YOUR OUTBOARD MOTOR.

  • Page 5: General Information

    EMU00004 Chapter 1 GENERAL INFORMATION IDENTIFICATION NUMBERS RECORD ..1-1 Outboard motor serial number ...1-1 Key number ...........1-1 EMISSION CONTROL INFORMATION...1-2 SAFETY INFORMATION......1-4 IMPORTANT LABELS ......1-6 BASIC BOATING RULES ......1-7 FUELING INSTRUCTIONS.....1-11 Gasoline ..........1-12 ENGINE OIL ..........1-13 BATTERY REQUIREMENT ....1-14 PROPELLER SELECTION .......1-15 START-IN-GEAR PROTECTION ....1-16...

  • Page 6: Identification Numbers Record

    Record your outboard motor serial num- ber in the spaces provided to assist you in 401015 ordering spare parts from your Yamaha dealer or for reference in case your out- board motor is stolen. 1 Outboard motor serial number...

  • Page 7: Emission Control Information

    EMU01385 EMISSION CONTROL INFORMATION EMU01387 NORTH AMERICAN MODELS This engine conforms to U.S. Environ- mental Protection Agency (EPA) regula- 108043 tions for marine SI engines. See the label affixed to your engine for details. Approval label of Emission control certificate This label is attached to the bottom cowl- ing.
  • Page 8 EMU01389 STAR LABELS Your outboard motor is labeled with a California Air Resources Board (CARB) star label. See below for a description of your particular label. 1 Star label 000850 One Star - Low Emission The one-star label identifies engines that meet the Air Resources Board’s 2001 exhaust emission standards.

  • Page 9: Safety Information

    EMU00917 8 This product emits exhaust gases which SAFETY contain carbon monoxide, a colorless, odorless gas which may cause brain INFORMATION damage or death when inhaled. Symp- toms include nausea, dizziness, and 8 Before mounting or operating the out- drowsiness. Keep cockpit and cabin board motor, read this entire manual.
  • Page 10 8 Be informed about boating safety. Addi- tional publications and information can be obtained from many organizations, including the following: United States Coast Guard Consumer Affairs Staff (G-BC) Office of Boating, Public, and Consumer Affairs U.S. Coast Guard Headquarters Washington, D.C. 20593-0001 Boating Safety Hotline: 1-800-368-5647 National Marine Manufacturers Association (NMMA)

  • Page 11: Important Labels

    EMU00014 IMPORTANT LABELS WARNING LABELS WARNING This engine is equipped with a neutral starting device. The engine will not start unless the shift control is in neutral position. 6E0-83627-41 202083 WARNING Be sure shift control is in neutral before starting engine. (except 2HP) Do not touch or remove electrical parts when starting or during operation.

  • Page 12: Basic Boating Rules

    EMU00015 Stand-on vessel BASIC BOATING RULES The vessel with the right-of-way has the duty to continue its course and speed, (Rules of the road) except to avoid an immediate collision. When you maintain your direction and Just as there are rules which apply when speed, the other vessel will be able to you are driving on streets and high ways, determine how best to avoid you.
  • Page 13 RULES WHEN ENCOUNTERING will clear one another if you continue on your set course and speed. VESSELS There are three main situations which you may encounter with other vessels which could lead to a collision unless the Steer- ing Rules are followed: Meeting (you are approaching another vessel head-on) Crossing (you are traveling across the...
  • Page 14 its course and speed. You must stay out Sailing vessel right-of-way of its way until you are clear of it. Like- Sailing vessels should normally be given wise, if another vessel is passing you, you the right-of-way. The exceptions to this should maintain your speed and direction are: so that the other vessel can steer itself...
  • Page 15 tion. These markers are white with black letters and orange boarders. They signify speed zones, restricted areas, danger areas, and general information. Remember, markings may vary by geo- graphic location. Always consult local boating authorities before driving your boat in unfamiliar waters. MAIN CHANNEL BUOYS "...

  • Page 16: Fueling Instructions

    EMU00016 FUELING INSTRUCTIONS GASOLINE AND ITS VAPORS ARE HIGH- LY FLAMMABLE AND EXPLOSIVE! 8 Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. 8 Stop engine before refueling. 8 Refuel in a well-ventilated area. Refuel portable fuel tanks off the boat.

  • Page 17: Gasoline

    EMU01804 GASOLINE Recommended gasoline: Regular unleaded gasoline with a minimum octane rating of 86 (Pump Octane Number) = (R+M)/2 If knocking or pinging occurs, use a differ- ent brand of gasoline or premium unlead- ed fuel. EMU00027 Gasohol There are two types of gasohol: gasohol containing ethanol and that containing methanol.

  • Page 18: Engine Oil

    EMU01769 ENGINE OIL Recommended engine oil: 4-stroke motor oil with a combination of corresponding SAE and API as shown in the chart. 10W-30 10W-40 Engine oil quantity: See Chapter 4, “Specifications.” All 4-stroke engines are shipped from the factory without engine oil. 001162 1-13...

  • Page 19: Battery Requirement

    EMU01775 BATTERY REQUIREMENT Do not use a battery that does not meet the specified capacity. If a battery which does not meet specifications is used, the electric system could perform poorly or be overloaded, causing electric system damage. For electric start models, choose a battery which meets the following specifications.

  • Page 20: Propeller Selection

    Conversely, a larger-pitch pro- peller is more suitable for a smaller oper- ating load. Yamaha dealers stock a range of pro- pellers, and can advise you and install a propeller on your outboard that is best suited to your application.

  • Page 21: Start-In-Gear Protection

    10-3/4 x 17 - G Refer to the section “CHECKING PRO- PELLER” for instructions on propeller removal and installation. 602011 EMU01209 START-IN-GEAR PROTECTION Yamaha outboard motors or Yamaha approved remote control units equipped with start-in-gear protection device(s). This feature permits the engine to be started only when it is Neutral.
  • Page 22 – MEMO –...

  • Page 23: Basic Components

    EMU00037 Chapter 2 BASIC COMPONENTS MAIN COMPONENTS......2-1 OPERATIONS OF CONTROLS AND OTHER FUNCTIONS ........2-2 Recoil starter handle......2-2 Multifunction tiller handle....2-2 Remote control........2-5 Trim tab..........2-10 Power trim/tilt switch......2-11 Warning indicator(s) ......2-11 Tachometer..........2-12 Trim meter ...........2-12 Tilt lock mechanism......2-13 Tilt support knob.........2-13 Top cowling lock lever .......2-13 Flushing device ........2-14 WARNING SYSTEM ......2-15...

  • Page 24: Main Components

    EMU01206 MAIN COMPONENTS 000707 000708 701016 x1000 r/min 101104 YAMAHA YAMAHA 801012 801011 1 Top cowling * w Multifunction tiller handle 2 Top cowling lock lever * e Steering friction adjusting lever 3 Oil drain bolt r Tilt support knob...

  • Page 25: Operations Of Controls And Other Functions

    EMU00039 OPERATIONS OF CONTROLS OTHER FUNCTIONS EMU00059 RECOIL STARTER HANDLE (If equipped) Pull the handle gently until resistance is 209022 felt. Then vigorously pull the handle straight out to crank the engine to start it. EMU00075 MULTIFUNCTION TILLER HANDLE The tiller handle centralized most of func- tions for the outboard motor operation.
  • Page 26 EMU00081 Throttle control grip The throttle control grip is on the tiller handle. Turn the grip counterclockwise to increase speed and clockwise to decrease speed. 501023 EMU00082 Throttle Indicator The fuel consumption curve on the throt- tle indicator shows the relative amount of fuel consumed for each throttle position.
  • Page 27 EMU00933 Engine Stop Lanyard Switch The lock-plate 1 must be attached to the engine stop lanyard switch for the engine to run. The lanyard 2 should be attached to a secure place on the operator’s cloth- ing, or arm or leg. Should the operator fall overboard or leave the helm, the lanyard will pull out the lock plate, stopping igni- 000980...

  • Page 28: Remote Control

    EMU00085 Engine Stop Button Pushing this button opens the ignition cir- cuit and stops the engine. 501063 EMU01150 Steering Friction Adjusting Lever A friction device provides adjustable resistance to the steering mechanism, and can be set according to operator pref- erence.
  • Page 29 EMU00098 Remote Control Lever Moving the lever forward from the Neu- tral position engages Forward gear. Pulling the lever back from Neutral engages Reverse. The engine will contin- ue to run at idle until the lever is moved about 35° (a detent can be felt). Moving the lever farther opens the throttle, and 701031 the engine will begin to accelerate.
  • Page 30 EMU00100 Neutral Throttle Lever To open the throttle without shifting into either Forward or Reverse, place the remote control lever in the Neutral posi- tion and lift the neutral throttle lever. NOTE: The neutral throttle lever will operate only when the remote control lever is in Neu- 701033* tral.
  • Page 31 EMU00934 Engine Stop Lanyard Switch The lock-plate 1 must be attached to the engine stop lanyard switch for the engine to run. The lanyard 2 should be attached to a secure place on the operator’s cloth- ing, or arm or leg. Should the operator fall overboard or leave the helm, the lanyard will pull out the lock plate, stopping igni- 000569...
  • Page 32 EMU01331 Power Trim/Tilt Switch The power trim/tilt adjusts the motor angle in relation to the transom. The power trim/tilt switch is located on the remote control lever grip. Pushing the switch “UP” trims the motor up, then tilts the motor up. Pressing the switch “DN” tilts the motor down and trims the motor 701034* down.

  • Page 33: Trim Tab

    EM00113 TRIM TAB The trim tab should be adjusted so that the steering control can be turned to either the right or left by applying the same amount of force. An improperly adjusted trim tab may cause difficult steering. Always test run after the trim tab has been installed or replaced to be sure steering is correct.

  • Page 34: Power Trim/Tilt Switch

    EMU01125 POWER TRIM/TILT SWITCH The power trim/tilt adjusts the motor angle in relation to the transom. The power trim/tilt switch is located on the side of the bottom engine cowling. Push- ing the switch “UP” trims the motor up, then tilts the motor up. Pressing the switch “DN”...

  • Page 35: Tachometer

    TACHOMETER This meter contains the following func- tions, 1 Tachometer 2 Low oil pressure warning lamp x1000 r/min 3 Overheat warning lamp YAMAHA EMU00126 801012* Tachometer This meter shows the engine speed. EMU00127 Low Oil Pressure Warning Lamp If oil pressure drops too low, this lamp will flash.

  • Page 36: Tilt Lock Mechanism

    EMU00154 TILT LOCK MECHANISM (for Hydro- tilt model) Tilt-lock mechanism is used to prevent reverse thrust from the propeller lifting the outboard motor when reversing. To lock it, set the tilt-lock lever in the Lock position. To release it, place the tilt-lock lever in the Tilt position.

  • Page 37: Flushing Device

    EMU01146 FLUSHING DEVICE This device 1 is used to clean the cooling water passages of the motor using a gar- den hose and tap water. NOTE: Refer to “Cleaning Cooling-water Pas- sages” in Chapter 4 for instructions on usage. 313023 2-14...

  • Page 38: Warning System

    EMU00169 WARNING SYSTEM Do not continue to operate the engine if the warning device has activated. Consult your Yamaha dealer if the problem can- not be located and corrected. 303021 EMU00170 OVERHEAT WARNING This engine has an overheat warning device. If the engine temperature rises too high, the warning device will activate.

  • Page 39: Low Oil Pressure Warning

    Check oil level and add oil as needed. 801013* If the oil level is correct, consult your Yamaha dealer. Do not continue to run the engine if the low oil pressure lamp is “ON”. Serious engine damage may occur.
  • Page 40 – MEMO –...

  • Page 41: Operation

    EMU00174 Chapter 3 OPERATION INSTALLATION ........3-1 Mounting the outboard motor ....3-2 BREAKING IN (RUNNING IN) ENGINE ..3-4 PRE-OPERATION CHECKS ......3-5 CHECKING THE ENGINE OIL LEVEL..3-6 FILLING FUEL ...........3-7 STARTING ENGINE .........3-8 WARMING UP ENGINE ......3-12 SHIFTING ..........3-13 Forward..........3-13 Reverse ..........3-14 STOPPING ENGINE .......3-15 TRIMMING OUTBOARD MOTOR..3-16 Adjusting trim angle ......3-17...

  • Page 42: Installation

    EMU00175 INSTALLATION Incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat or accessories such as transom ladders/depth finder trans- ducers) can create airborne water spray while the boat is cruising. Severe engine damage may result if the motor is operat- ed continuously in the presence of air- borne water spray.

  • Page 43: Mounting The Outboard Motor

    EMU00176 MOUNTING THE OUTBOARD MOTOR Improper mounting of the outboard motor could result in hazardous condi- tions such as poor handling, loss of con- trol, or fire hazards. Observe the follow- ing: 8 The information presented in this sec- tion is intended as reference only. It is possible provide complete...
  • Page 44 Overpowering a boat may cause severe instability. Do not install an outboard motor with more horsepower than the maximum rating on the capacity plate of the boat. If the boat does not have a capacity plate, consult the boat manufac- turer.

  • Page 45: Breaking In (Running In) Engine

    EMU00224 BREAKING IN (RUNNING IN) ENGINE Your new engine requires a period of break-in (running-in) to allow mating sur- faces of moving parts to wear-in evenly. Correct break-in (running-in) will help ensure proper performance and longer engine life. Failure to follow the break-in (running-in) procedure may result in reduced engine life or even severe engine damage.

  • Page 46: Pre-Operation Checks

    EMU00204 PRE-OPERATION CHECKS If any item in the pre-operation check is not working properly, have it inspected and repaired before operating the out- board motor. Otherwise, an accident could occur. Do not start the engine out of water. Overheating and serious engine damage can occur.

  • Page 47: Checking The Engine Oil Level

    EMU00209 Controls 8 Check throttle, shift, and steering for proper operation before starting the engine. 8 The controls should work smoothly, without binding or unusual free play. 8 Look for loose or damaged connec- tions. 8 Check operation of the starter and stop switches when the outboard motor is in the water.

  • Page 48: Filling Fuel

    While many additives available may reduce deposits, Yamaha recommends the use of Ring Free Fuel Additive, avail- able from your Yamaha dealer. Ring Free has repeatedly proven its ability to clean combustion deposits from inside the engine, notably the critical piston-ring- land area, and fuel system components.

  • Page 49: Starting Engine

    EMU01147 STARTING ENGINE 8 Before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you. 8 When the air vent screw is loosened, gasoline (petrol) vapor will be released.
  • Page 50 EMU01497 PROCEDURE FOR TILLER CONTROL MODEL 4) Place the gear-shift lever in the neu- tral position. NOTE: The start-in-gear protection device pre- vents the engine from starting except when in Neutral. 501055 5) Attach the engine stop switch lanyard to a secure place on your clothing, or your arm or leg.
  • Page 51 EMU01005 Manual Start Model 7) Pull the starter handle slowly until you feel resistance. Then, give a strong pull straight out to crank and start the engine. Repeat it, if neces- sary. NOTE: If the warm engine fails to start, open the 209022 throttle slightly and try to start the engine.
  • Page 52 8 Attach the engine stop switch lanyard START to a secure place on your clothing, your arm or leg while operating. 8 Do not attach the lanyard to clothing that could tear loose. Do not route the lanyard where it could become entan- gled, preventing from functioning.

  • Page 53: Warming Up Engine

    Check the oil level and add oil if necessary. If the cause for the low oil pressure warning indicator cannot be found, consult your Yamaha dealer. 8 A continuous flow of water from the pilot hole shows that the water pump is pumping water through the cooling passages.

  • Page 54: Shifting

    EMU00261 SHIFTING Before shifting, make sure there are no swimmers or obstacles in the water near you. To change the shifting position from for- ward to reverse or vice-versa, close the throttle first so that the engine idles (or runs at low speeds). EMU00265 FORWARD Tiller control model...

  • Page 55: Reverse

    EMU01326 REVERSE When operating in Reverse, go slowly. Do not open the throttle more than half. Oth- erwise, the boat may become unstable, which could result in loss of control and an accident. 501012 1) Place the throttle control grip in the fully closed position (for Tiller control model).

  • Page 56: Stopping Engine

    EMU00273 STOPPING ENGINE Let it cool off for a few minutes at idle or low speed first. Stopping the engine immediately after operating at high speed is not recommended. 501063 EMU00277 1) Push and hold the engine stop button or turn the main switch to “OFF”. START 701023 2) If the fuel joints are provided, discon-...

  • Page 57: Trimming Outboard Motor

    EMU01412 TRIMMING OUTBOARD MOTOR The trim angle of the outboard motor helps determine the position of the bow of the boat in the water. The correct trim angle will help improve performance and fuel economy while reducing strain on the engine.

  • Page 58: Adjusting Trim Angle

    ADJUSTING TRIM ANGLE EMU01113* Hydro-tilt Model 8 Stop the engine before adjusting the trim angle. 8 Be sure all people are clear of the out- board motor when adjusting the tilt angle, also be careful not to pinch any body parts between the drive unit and clamp bracket.
  • Page 59 EMU01116* Power Trim/Tilt Model 8 Be sure all people are clear of the out- board motor when adjusting trim/tilt angle, also be careful not to pinch any body parts between the drive unit and clamp bracket. 8 Use caution when trying a trim position for the first time.
  • Page 60 EMU19160 Trim angle settings and boat handling When the boat is on plane, a bow-up atti- tude results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees.

  • Page 61: Tilting Up/Down

    NOTE: Depending on the type of boat, the out- board motor trim angle may have little effect on the trim of the boat when oper- ating. EMU00285 TILTING UP/DOWN If the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the propeller and casing from damage by collision with obstructions, and also to...
  • Page 62 EMU01127 PROCEDURE FOR TILTING UP Hydro-tilt model 1) Remove the fuel-line connection from the motor. 304053 2) Place the tilt-lock lever in the release position. 402076 3) Hold the rear of the top cowling with one hand, tilt the engine up, push the tilt support knob into the clamp brack- et, and place the tilt-lock lever back into the lock position to support the...
  • Page 63 2) Push the power trim/tilt switch “UP” until the outboard has tilted up com- pletely. 701034* 3) Push the tilt support knob into the clamp bracket to support the engine. After tilting the engine, be sure to sup- port it with the tilt support knob. Other- wise, the engine could fall back down suddenly if oil in the power trim/tilt unit should lose pressure.

  • Page 64: Cruising In Shallow Water

    EMU00307 CRUISING IN SHALLOW WATER Hydro tilt model The engine can be tilted up partially to allow operation in shallow water. 000702 8 Place the gear shift in the Neutral posi- tion before setting for the shallow water cruising. 8 Return the engine to its normal posi- tion as soon as the boat is back in deeper water.

  • Page 65: Cruising In Other Conditions

    EMU00316 CRUISING IN OTHER CONDITIONS CRUISING IN SALT WATER After operating in salt water, wash out the cooling-water passages with fresh water to prevent them from becoming clogged- up with salt deposits. NOTE: Refer to cooling system flushing instruc- tions in “TRANSPORTING AND STORING OUTBOARD MOTOR”.
  • Page 66 – MEMO –...

  • Page 67: Maintenance

    EMU00317 Chapter 4 MAINTENANCE SPECIFICATIONS ........4-1 TRANSPORTING AND STORING OUTBOARD MOTOR .......4-3 Trailering outboard motor ....4-3 Storing outboard motor .......4-4 PERIODIC MAINTENANCE......4-9 Replacement parts ........4-9 Maintenance chart ......4-10 Greasing..........4-11 Cleaning and adjusting spark plug ...4-12 Checking top cowling ......4-13 Checking fuel system ......4-14 Inspecting fuel filter ......4-15 Inspecting idling speed ......4-16 Changing engine oil......4-17...

  • Page 68: Specifications

    EMU00322* SPECIFICATIONS Model Unit F30TRC Item DIMENSIONS Overall Length mm (in.) 700 (27.6) Overall Width mm (in.) 378 (14.9) Overall Height mm (in.) —/1,340 (52.8) Transom height mm (in.) —/533 (21.0) Weight kg (lb.) —/91 (200) PERFORMANCE Full throttle operating range r/min 5,000 ~ 6,000 Maximum output...
  • Page 69 F40MHC F40ERC F40TRC 1,332 (52.4) 700 (27.6) 700 (27.6) 378 (14.9) 378 (14.9) 378 (14.9) 1,217 (47.9)/1,340 (52.8) 1,217 (47.9)/ — — /1,340 (52.8) 410 (16.1)/533 (21.0) 410 (16.1) /— — /533 (21.0) 83* (183)/87* (192) 82* (181) /— — /89* (196) 5,000 ~ 6,000 5,000 ~ 6,000 5,000 ~ 6,000...

  • Page 70: Transporting And Storing Outboard Motor

    For further details, consult your Yamaha dealer. 8 Never get under the lower unit while it is tilted, even if a motor support bar is used.
  • Page 71 “Yamaha Fuel Conditioner and Stabilizer” (Part No. LUB-FUELC-12- 00) to each gallon of fuel. NOTE: The use of “Yamaha Fuel Conditioner and Stabilizer” eliminates the need to drain the fuel system. Consult your Yamaha dealer or other qualified mechanic if the...
  • Page 72 4) Run the engine at a fast idle for 10~15 minutes. 5) Just prior to turning off the engine, quickly spray “Yamaha Stor-Rite Engine Fogging Oil” (Part No. LUB- STRRT-12-00) alternately into each carburetor. When properly done, the engine will smoke excessively and...
  • Page 73 When properly done, the engine will smoke excessively 605014 and almost stall. 5) Remove the flushing attachment and wipe off any excess water. 6) Install the top cowling and the pro- peller. NOTE: A flushing attachment is available from a Yamaha dealer.
  • Page 74 1) Wash down the exterior of the out- board with fresh water and dry off completely. 2) Spray the engine’s exterior with “Yamaha Silicone Protectant” (Part No. LUB-SILCNE-13-00). 3) Wax the cowling with a non-abrasive wax such as “Yamaha Silicone Wax” (Part No. ACC-11000-15-02).
  • Page 75 EMU00353 Battery Care Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. It con- tains sulfuric acid. Avoid contact with skin, eyes, or clothing. Antidote: EXTERNAL; Flush with water. INTERNAL; Drink large quantities of water or milk. Follow with milk of mag- nesia, beaten egg, or vegetable oil.

  • Page 76: Periodic Maintenance

    Be sure to turn off the engine when you perform maintenance unless otherwise specified. If the owner is not familiar with machine servicing, this work should be done by a Yamaha dealer or other quali- fied mechanic. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine engine repair establishment or individual.

  • Page 77: Maintenance Chart

    Refer to the sections in this chapter for explanations of each owner-specific action. The mark (G) indicates the check-ups which you may carry out yourself. The mark (1) indicates work to be carried out by your Yamaha dealer. Initial Every...

  • Page 78: Greasing

    Every Item Actions 500 hours 1000 hours (2.5 years) (5 years) Timing belt Replacement EMU00366 GREASING Yamaha marine grease (Water resistant grease) 103211 4-11...

  • Page 79: Cleaning And Adjusting Spark Plug

    Do not attempt to diagnose any problems yourself. Instead, take the outboard motor to a Yamaha dealer. You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode.

  • Page 80: Checking Top Cowling

    1 Spark plug gap 2 Spark plug I.D. mark (NGK) EMU16350 CHECKING TOP COWLING Check the fitting of the top cowling by pushing it with both hands. If the fitting is loose have it repaired by a Yamaha dealer. 4-13...

  • Page 81: Checking Fuel System

    EMU00369 CHECKING FUEL SYSTEM Gasoline (petrol) and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames or other sources of ignition. Check the fuel line for leaks, cracks, or malfunctions. If any problem is found, it should be repaired immediately by Yama- ha dealer or other qualified mechanic.

  • Page 82: Inspecting Fuel Filter

    EMU00374 Check the fuel filter periodically. The fuel filter is a one-piece, disposable type. If foreign matter is found in the fil- ter, replace it. For replacement of the fuel 207061 filter, consult a Yamaha dealer. 4-15...

  • Page 83: Inspecting Idling Speed

    If not warmed up fully, the idle speed will measure higher than normal. If you have difficulty verifying the idle speed, or the idle speed requires adjustment, consult a Yamaha dealer or other qualified mechan- 4-16...

  • Page 84: Changing Engine Oil

    EMU01415 CHANGING ENGINE OIL 8 Avoid draining the engine oil immedi- ately after stopping the engine. The oil is hot and should be handled with care to avoid burns. 8 Be sure the outboard is securely fas- tened to the transom or a stable stand. 8 Change the engine oil after the first 10 hours of operation, and every 100 hours or at 6-month intervals thereafter.
  • Page 85 If the oil lamp does not turn off, or if there are oil leaks, stop the engine and find the cause. Continued operation with a problem could cause severe engine damage. If the problem cannot be found and corrected, consult your Yamaha deal- 4-18...
  • Page 86 7) Dispose of used oil according to local regulations. 201012* NOTE: 8 For disposal of used oil consult your Yamaha dealer. 8 The oil should be changed more often when the engine is operated under adverse conditions such as extended trolling.

  • Page 87: Replacing Fuse

    This could cause electrical system damage and a fire haz- ard. NOTE: If the new fuse blows again immediately, consult a Yamaha dealer. 1 Fuse box 2 Fuse (20A) 205052 3 Spare fuse (20A) 4 Fuse puller...

  • Page 88: Checking Power Trim And Tilt System

    5) Operate the motor to trim and tilt down. Check that the trim and tilt rod operates smoothly. NOTE: If any operation is abnormal, consult a Yamaha dealer. 411036 Recommended fluid; Yamaha power trim & tilt fluid or ATF (DEXRON-II) 4-21...

  • Page 89: Checking Propeller

    EMU00388 CHECKING PROPELLER You could be seriously injured if the engine accidentally starts while you are near the propeller. 8 Before inspecting, removing installing the propeller, remove the 210021 spark plug caps from the spark plugs. Also, put the shift control in Neutral, put the main switch in the “OFF”...
  • Page 90 8 Be sure to use a new cotter pin and bend the ends over securely. Other- wise, the propeller could come off dur- ing operation and be lost. 1) Apply Yamaha Marine grease or Cor- rosion resistant grease to the pro- peller-shaft. 2) Install the thrust washer and propeller on the propeller-shaft.

  • Page 91: Changing Gear Oil

    Inspect the used oil after it has been drained. If the oil is milky, water is get- ting into the gear-case which can cause gear damage. Consult a Yamaha dealer for repair of the lower unit seals. NOTE: For disposal of used oil consult your Yamaha dealer.

  • Page 92: Inspecting And Replacing Anode(S)

    604016 Inspect the external anodes periodically. Remove scales from the surfaces of the anodes. Consult a Yamaha dealer for replacement of external anodes. Do not paint anodes, as this would ren- der them ineffective. NOTE:...

  • Page 93: Checking Battery

    EMU04041 CHECKING BATTERY (for Electric start models) Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poi- sonous and highly caustic. Always follow these preventive mea- sures: 8 Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury.
  • Page 94 3) If the battery will be stored for longer than a month, check the specific grav- ity of the fluid at least once a month and recharge the battery when it is low. NOTE: Consult a Yamaha dealer when charging or re-charging batteries. 4-27...
  • Page 95 EEMU01279 Connecting the Battery Mount the battery holder securely in a dry, well-ventilated, vibration-free loca- tion in the boat. Install a fully charged battery in the holder. 8 Make sure the main switch (on applica- ble models) is “OFF” before working on the battery.

  • Page 96: Checking Bolts And Nuts

    EMU00408 CHECKING BOLTS AND NUTS 1) Check that bolts securing the cylinder head and engine and the nut securing the flywheel are tightened with their specified tightening torque. 2) Check the tightening torque of other bolts and nuts. EMU01172 CLEANING COOLING-WATER PASSAGES Flushing device equipped model Perform this procedure right after opera-...

  • Page 97: Motor Exterior

    Check the motor for scratches, nicks, or flaking paint. Areas with damaged paint are more likely to corrode. If necessary, clean and paint the areas. A touch-up paint is available from a Yamaha dealer. EMU00413 COATING THE BOAT BOTTOM A clean hull improves boat performance.
  • Page 98 – MEMO –...

  • Page 99: Trouble Recovery

    EMU00414 Chapter 5 TROUBLE RECOVERY TROUBLESHOOTING ......5-1 TEMPORARY ACTION IN EMERGENCY ..........5-5 Impact damage ........5-5 Power trim/tilt will not operate....5-5 Starter will not operate......5-6 Treatment of submerged motor..5-9...

  • Page 100: Troubleshooting

    A problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. The troubleshooting chart describes basic checks and possi- ble remedies. (This chart covers all Yamaha outboard motors. Therefore, some items may not apply to your model.) If your outboard motor requires repair, bring it to a Yamaha dealer.
  • Page 101 3. Fill tank with clean, fresh fuel. 4. Fuel filter clogged. 4. Clean or replace filter. 5. Failed ignition parts. 5. Have serviced by a Yamaha dealer. 6. Warning system activated. 6. Find and correct cause of warning. 7. Spark plug gap incorrect.
  • Page 102 5. Engine oil contaminated or 5. Replace oil with fresh, specified sounds or deteriorated. type. indicator lamp 6. Oil filter clogged. 6. Have serviced by a Yamaha lights. dealer. 7. Oil feed/injection pump 7. Have serviced by a Yamaha malfunctions. dealer.
  • Page 103 13. Check wires for wear or breaks. ignition wiring. Tighten all loose connections. Replace worn or broken wires. 14. Failed ignition parts. 14. Have serviced by a Yamaha dealer. 15. Specified engine oil not used. 15. Check and replace oil with specified type.

  • Page 104: Temporary Action In Emergency

    607011 3) Whether damage is found or not, return to the nearest harbor slowly and carefully. 4) Have a Yamaha dealer inspect the outboard motor before operating it again. EMU00419 POWER TRIM/TILT WILL NOT OPERATE...

  • Page 105: Starter Will Not Operate

    EMU00423 STARTER WILL NOT OPERATE If the starter mechanism does not operate (engine cannot be cranked with the starter), the engine can be started with an emergency starter rope. 8 Use this procedure only in an emer- gency and only to return to port for repairs.
  • Page 106 EMU01130 Emergency Starting Engine 1) Remove the top cowling. 2) If the engine is equipped with a start- in-gear protection cable, remove it 1 by pulling it out from the starter. 208075 3) Remove the starter/flywheel cover by removing the 4 bolts. 208076 ER/TR 208081...
  • Page 107 5) Insert the knotted end of the emer- gency starter rope into the notch in the flywheel rotor and wind the rope several turns clockwise. 6) Pull the rope slowly until resistance is felt. 7) Give a strong pull straight out to crank and start the engine.

  • Page 108: Treatment Of Submerged Motor

    6) Take the outboard motor to a Yamaha dealer as soon as possible. Do not attempt to run the motor until it has been completely inspected.

  • Page 109: Index

    EMU00450 Chapter 6 INDEX INDEX............6-1...
  • Page 110 EMU00451 INDEX Filling fuel ..........3-7 Flushing cooling system and fogging engine .........4-5 Adjusting trim angle......3-17 Flushing device ........2-14 Forward...........3-13 Basic boating rules ........1-7 Fueling instructions .......1-11 Battery care..........4-8 Battery requirement ......1-14 Gasoline ..........1-12 Breaking in (running in) engine....3-4 Gear shift lever .........2-2 Greasing..........4-11 Changing engine oil ......4-17 Changing gear oil........4-24...
  • Page 111 Overheat warning lamp ......2-12 Treatment of submerged motor ....5-9 Trim angle settings and Periodic maintenance......4-9 boat handling .........3-19 Power trim/tilt switch .....2-9, 2-11 Trim meter ..........2-12 Power trim/tilt will not operate....5-5 Trim tab...........2-10 Pre-operation checks .......3-5 Trimming outboard motor....3-16 Propeller selection .........1-15 Troubleshooting........5-1 Recoil starter handle........2-2 Warming up engine.......3-12...
  • Page 112 1. Be sure your new Yamaha is registered for warranty. Your boat dealer should do this at the time of sale. Make sure your dealer gives you a copy of the completed Yamaha regis- tration card for your records.
  • Page 113 5. Your warranty applies specifically to repairs made in the country of purchase. If your U.S.-purchased Yamaha needs warranty service while in Canada, or your Canadian pur- chased Yamaha needs service while in the United States, Yamaha will assist the local dealer whenever possible. However, some products available in one country may not be sold or serviced in the other.
  • Page 114 Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha 1999-or-later model four-stroke outboard motors originally dis- tributed by Yamaha Motor Corporation, U.S.A. will be free from defects in material and workmanship for the period of time stated here- in, subject to certain stated limitations. Warranty coverage for outboards distributed by non-US Yamaha affiliated companies may be different.
  • Page 115 Charges for removal of the motor from a boat and transporting the motor to and from an authorized Yamaha Outboard Motor Dealer are excluded from warranty coverage.
  • Page 116 The federal government requires each manufacturer of a motor vehicle to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A.
  • Page 117 Yamaha outside the U.S.A. or Canada, please contact an autho- rized Yamaha dealer in your country. Keep a copy of your sales contract or invoice for the purchase of your Yamaha and present it if you need warranty repairs. This document should show the date of purchase, which is important evidence the repairing dealer will need to be sure your Yamaha is covered by warranty.
  • Page 118 Printed in Japan April 2003-0.7 × 1 ! 67C-28199-14 (F30AET, F40BMHD, F40BED, F40BET) Printed on recycled paper...
  • Page 119 (A l’usage du concessionnaire) MODÉLE ET NO. DE SÉRIE DU MOTEUR HORS-BORD (sur l’étiquette d’identification de la presse de fixation) YAMAHA DEALER NUMBER NO. DU CONCESSIONNAIRE YAMAHA DEALER NAME YAMAHA MOTOR CO., LTD. NOM DU MADE IN JAPAN CONCESSIONNAIRE PAYS D'ORIGINE JAPON USAGE...
  • Page 120 PLACE POSTAGE HERE ATTN: WARRANTY DEPARTMENT...

This manual is also suitable for:

F40c

Table of Contents