Information Code Table - Panasonic DX-2000 Service Manual

4.8.

Information Code Table

Code Mode
001 RCV
COPY
002 RCV
COPY
003 RCV
COPY
007 RCV
COPY
008 RCV
COPY
010 RCV
COPY
011 STANDBY
012 RCV
021 STANDBY
RX
COPY
026 -
030 XMT
031 XMT
COPY
033 -
041 STANDBY
RX
COPY
043 STANDBY
RX
COPY
045 STANDBY
051 RCV
COPY
054 STANDBY
RX
COPY
055 STANDBY
RX
COPY
058 -
059 RCV
COPY
060 -
061 -
063 -
064 -
200 RCV
212 XMT
RCV
301 XMT
RCV
331 XMT
Phase Description of Problem
C, D Leading edge of the recording paper fails to
reach the Timing Sensor. (1st cassette)
C, D Leading edge of the recording paper fails to
reach the Timing Sensor. (2nd cassette)
C, D Leading edge of the recording paper fails to
reach the Timing Sensor. (3rd cassette)
C, D 1. Leading edge of the recording paper fails to
reach the Eject Sensor.
2. Recording paper has not completely passed
the Eject Sensor.
C, D Paper Cassette was opened while the recording
paper was feeding.
B, C No recording paper.
- Paper Cassette is not installed properly.
C, D The length of the received document is over
380 mm. (Used in France only)
B, C, D Fan is abnormal.
Thermister is abnormal.
Fuser Control is abnormal.
- The backup battery is getting weak.
B Read Point Sensor does not go ON within 10
seconds after the document starts feeding.
C Transmitting document was longer than
2,000 mm (or 78.7 in).
- Sub CPU system error.
B, C, D Out of toner.
B, C, D Low Toner.
- No Toner Cartridge.
- Printer Motor is abnormal.
- HSYNC is abnormal.
Laser motor is abnormal.
- No response of LBP CPU on LPC.
A Interface error occurred with the
500-sheet optional cassette feeder.
C Interface error occurred between FCB PCB and
LPC PCB.
A Printer Cover is open.
A ADF Door is open.
A Jam Access Cover is open.
A Jam Access Cover is open.
C Decoding process is not completed at the end of
phase C.
A-E Interface error occurred between the CPU and
modem.
- System fault.
C 8-minutes timer error. (Germany only)
Information Codes
183
Cause
Recording paper jam.
Timing Sensor abnormal.
Recording paper jam.
Timing Sensor abnormal.
Recording paper jam.
Timing Sensor abnormal.
Recording paper jam.
Eject Sensor abnormal.
Recording paper jam.
No recording paper or paper is not set
properly.
No paper Sensor is defective.
Defective LPC PCB.
Defective Fuser Unit, LVPS or Fan.
Document is not set properly.
Defective Read Point Sensor.
The document may jam.
Defective Read Point Sensor.
Defective FCB PCB.
No toner.
Defective Toner Sensor.
Toner is getting low.
Defective Toner Sensor.
Toner cartridge has not been installed.
Defective Toner Sensor (Cartridge Sensor).
Connector not properly connected.
Defective Printer Motor.
Defective LPC PCB.
Defective Laser Unit.
Defective LPC PCB.
Defective FCB PCB.
Defective CST3 PCB.
Defective LPC PCB.
Defective FCB PCB.
Cover is not firmly closed.
Connectors are not firmly connected.
Cover is not firmly closed.
Connectors are not firmly connected.
Cover on the optional 2nd cassette is
not closed.
Cover on the optional 3rd cassette is not
closed.
Defective FCB PCB.
Modem is defective. (FCB PCB)
Software problem occurred. (FCB PCB)
Software problem occurred. (FCB PCB)