Panasonic DX-2000 Service Manual page 195

No. Parameter (see Note 3)
000 MON/TEL DIAL
001 ALARM STATUS
002 STOP COMM. JRNL
003 Not Used
004 NUMERIC ID SET
005 Not Used
006 ID DISPLAY
007 JNL COLUMN
008 MONITOR
009 DC LOOP
010 TX LEVEL
011 RX LEVEL
012 DTMF LEVEL
013 G3 RX EQL
014 G3 TX EQL
015 Not Used
~
016
017 TX START
018 RX START
019 ITU-T V.34
Function Parameter Table
Selections
1 = Monitor
2 = TEL/DIAL
1 = OFF
2 = Timer (6 sec.)
3 = Constant
1 = Off
2 = On
1 = Off (will not accept)
2 = On (accepts)
1 = Number (Numeric ID)
2 = Chara (Character ID)
1 = Preset station name
2 = Received ID
1 = Off
2 = On
1 = Off (Normal)
2 = On (Off Hook)
00 = 0 dBm
~
15 = -15 dBm
1 = -43 dBm
2 = -38 dBm
3 = -33 dBm
4 = -48 dBm
00 = 0 dBm
~
15 = -15 dBm
1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dB
1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dB
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = Off
2 = On
3 = Select
195
Function
Selects whether the machine starts to
automatically during On-Hook dialing.
Monitor : Start to TX after pressing START
TEL/DIAL : Start to TX automatically
Selects the No Paper or No Toner alarm status.
OFF : Alarm is disabled.
Timer : Alarm will shut off after 6 seconds.
Constant : Alarm will not stop until "STOP" is
pressed or the error is cleared/corrected.
Selects whether the machine prompts to print the
COMM. Journal when the printout condition is set
to INC and STOP is pressed during
communication.
Selects whether the machine accepts and allows to
set or change the Numeric ID.
Selects the priority of displaying the ID.
Selects the contents of the ID to display on the
Journal.
Selects whether the Monitor is ON/OFF for
monitoring fax signals.
(FOR SERVICE USE ONLY)
Selects a false Off Hook state for back to back
communication test.
Selects the TX signal output level, 0 to -15 dBm in 1
dBm steps. (Refer to Chapter 4.3)
Selects the receiving sensitivity of -33/-38/-43/-48
dBm.
(Refer to Chapter 4.3)
Selects the DTMF output level, 0 to -15 dBm in 1
dBm steps.
Selects the cable equalizer for G3 reception mode,
0dB, 4dB, 8dB or 12dB.
Selects the cable equalizer for G3 transmission
mode, 0dB, 4dB, 8dB or 12dB.
Selects the transmission modem start speed,
14400/12000/TC9600/TC7200/9600/7200/4800/
2400 bps.
Note: This parameter is applicable only when com-
municating with regular G3 machines. When com-
municating with Super G3 (V.34) machines, use
Parameter No. 32.
Selects the reception modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
Note: This parameter is applicable only when
communicating with regular G3 machines. When
communicating with Super G3 (V.34) machines,
use Parameter No. 33.
Selects whether the ITU-T V.34 is Off, On or Select.
Select: Select whether the ITU-T V.34 is Off or On,
when entering One-Touch/Abbreviated Dialing
Numbers or Manual Number Dialing.
TX