Programming Text Using The Keypad - Bosch Solution 16i User Manual

Solution 16 User Guide
i
performed. See the table below. If no keys are pressed for
20 seconds then the panel will play the exit jingle before
automatically terminating the session and hanging up.
Pressing [#] + [#] at any time while connected will cause
the control panel to terminate the session.
DTMF CO NT ROL FUN C TI O N S
Operation Command
Quick Arm
All Areas
Log In
USER PIN
OK
Log In
USER PIN
Failed
Turn Area
1
+ (Area Nº1-4) +
ON
Turn Area
1
+ (Area Nº1-4) +
OFF
Turn
Output 2
+ (Output Nº1-8) +
ON
Turn
Output 2
+ (Output Nº1-8) +
OFF
End
Session
Table 6: DTMF Remote Control Functions
DTMF E XAMPL ES
Examples below shows the log on step for clarity. In
practise is only necessary to log on once per DTMF control
session.
To turn Area 1 ON enter the following
2 + 5 + 8 + 0 + #
1 + 1 + 1 + #
To turn Output 7 ON enter the following
2 + 5 + 8 + 0 + #
2 + 7 + 1 + #
To turn Output 3 OFF enter the following
2 + 5 + 8 + 0 + #
2 + 3 + 2 + #
If the DTMF Quick Arm option is programmed then it
i
is possible to remotely arm all areas without logging
Note
onto the panel.
Simply enter [0] + [#] following the welcome jingle.
Make sure that the phone being used to remotely
control the panel is set to transmit DTMF tones when
keys are pressed during the call.
This option is disabled by default on some phones.
10
Response
0 #
2 x Beeps
+
Welcome
#
+
Jingle
# Long Beep
+
2 x Beeps
1 #
+
(Low - High)
2 x Beeps
2 #
+
(High - Low)
2 x Beeps
1 #
+
(Low - High)
2 x Beeps
2 #
+
(High - Low)
# Exit Jingle
# +
= Log ON
= Arm Area 1
= Log ON
= Turn Output 7 ON
= Log ON
= Turn Output 3 OFF

Programming Text Using The Keypad

When programming text via the keypad, each numeric key
represents a different group of characters.
Pressing the same numeric key again will move to the next
character assigned to the key (eg. Press the [2] key will
display the 'A' character, press the [2] key again will move
to the 'B' character, press the [2] key again will move to the
'C' character etc).
Once the required character is displayed, use the arrow
keys to move to the next letter of the word you are
entering. If you press a different key the system will assume
you are entering the next character in the word and it will
automatically step forward 1 position.
The key assignments and programming function are
identical to those found on most fixed and mobile phones.
Refer to the table below for detailed character information.
Key Characters Assigned To Each Numeric Key
1 _ -
2 A B
3 D E
4 G H
5 J K
6 M N
7 P Q
8 T U
9 W X
0 SPACE 0
Scroll Up through entire character list

Scroll Down through entire character list

Move to left one character position

Move to right one character position

OFF Clear from cursor postiion to end of line
Table 7: Text Character Set
To save programming changes, press [OK], or press [MENU]
to exit without saving.
The following additional
available by scrolling using the [
+ - @ # $ " & % * : ( ) / < > =
@ . 1
C 2
F 3
I 4
L 5
O 6
R S 7
V 8
Y Z 9
special characters
] and [] arrow keys.

Bosch Security Systems 6/09 BLCC500U FTR1.03
are