Data Field Programming; About Data Field Programming; Programming Data Fields; System Setup Fields (∗20 - ∗29) - ADT Safewatch Pro 3000EN Installation And Setup Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About Data Field Programming

The following pages list this control's data fields in numerical order. Field numbers are listed in the
left column followed by a "Title and Data Entries" column, which lists the valid entries for each field.
Experienced installers can simply follow this column when programming the data fields. The
"Explanation" column provides explanatory information and special notes where applicable.
Use the blank programming form to record the data for this installation.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields.
Start Data Field programming by entering the installer code + 8 + 0 + 0.
System Setup Fields (∗ ∗ ∗ ∗ 20 – ∗ ∗ ∗ ∗ 29)
FIELD TITLE and DATA ENTRIES
Installer Code
*20
Enter 4 digits, 0000-9999
Quick Arm Enable
*21
0 = do not allow quick arm
1 = allow quick arm
RF Jam Option
*22
0 = no RF jam detection
1 = send RF jam report
Quick (Forced) Bypass
*23
0 = no quick (forced) bypass
1 = allow quick bypass (code + [6] + [#])
RF House ID Code
*24
00 = disable all wireless touchpad
usage
01–31 = House ID for partition 1, 2 and
common
Chime By Zone/KP Sound Enables
*26
Entry 1
0 = no Entry 1 touchpad trouble sounds AND
no chime by zone (touchpad chimes on
fault of any entry/exit or perimeter zone
when chime mode is on)
1 = Chime by Zone enabled (select zones
to chime on zone list 3, using *81 Menu
mode)
2 = Communication Device (LRR) Trouble
sounding enabled (for communication
devices such as GSMV-ADT)
4 = System Low Battery sounding enabled
7 = select all entry 1 options
Entry 2
0 = no Entry 2 touchpad trouble sounds
1 = RF Supervision sounding enabled
2 = RF Low Battery sounding enabled
4 = RF Jam sounding enabled
7 = select all entry 2 options

Data Field Programming

EXPLANATION
The Installer Code is used to enter programming mode and to
assign the 4-digit Master Security Code (see "Master Code" in
the System Operation section for procedure). For security
purposes, the factory default installer code should be changed.
If enabled, a user code is not needed to arm the system.
Instead, users can press the [#] followed by an arming key to
arm the system.
However, a user code is always needed to disarm the system.
If enabled, a report is sent if the system detects an RF
jamming signal.
UL installations must be 1 if wireless devices are used.
All zones bypassed by this function will be displayed after the
bypass is initiated.
UL installations must be 0 (no forced bypass)
The House ID identifies receivers and wireless touchpads. If a
5827 or 5827BD Wireless Touchpad or 5804BD Transmitter is
being used, a House ID code must be entered, and the
touchpad should be set to the same House ID. You can assign
RF house ID for each partition.
If enabled, you can define the specific zones intended to chime
when faulted while the system is in Chime mode. Use zone
list 3 to assign these zones (see ∗81 Zone List Programming
section for details).
Keypad trouble sounding can be enabled/disabled for the
conditions listed for each entry below.
For each entry, enter the sum of the desired options.
Example Entry 1: for Chime by Zone and System Low
Battery sounding, enter 5. To enable all options, enter 7.
S E C T I O N
4-1
4