To Enter Programming Mode; To Exit Programming Mode - ADT Safewatch Pro 3000 Programming Manual

TO ENTER PROGRAMMING MODE:

Local programming requires the use of a Custom English touchpad connected to the touchpad terminals on the control.
1. POWER UP, then depress [
OR
2. Initially, key: Installer Code (6 + 3 + 2 + 1) plus 8 + 0 + 0.
OR
3. If different Installer Code is programmed, key: New Installer Code + 8 + 0 + 0.
✱
(if 98 was used to exit previously, method 1 above must be used to enter the program mode again)
Data Field Programming Procedures
Task
Go to a Data Field
Entering Data
Review a Data Field
Deleting an Entry
Interactive Mode Programming (∗56, *57, ∗58, ∗80, ∗81, ∗82)
Press [ ✱ ] + [Interactive Mode No.] (for example, ✱ 56). The Custom English display touchpad will display the first of a series of
prompts requesting entries.
Interactive Mode
✱
56 Zone Programming
✱
57 Function Key Programming
✱
58 Zone Programming
(Expert mode)
✱ 79 Output Device Mapping
✱
80 Output Programming
✱
81 Zone List Programming
✱
82 Alpha Programming
INITIALIZE DOWNLOAD and RESET DEFAULTS
✱
96 Initializes download ID and subscriber account number.
✱
97 Sets all data fields to original factory default values.

TO EXIT PROGRAMMING MODE:

✱
98 Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0. If
mode, system must be powered down, and method 1 above used to enter the programming mode.
✱
99 Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or method 1 above.
Special Messages
OC = OPEN CIRCUIT (no communication between Touchpad and Control).
EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).
After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.
This will revert to a "Ready" message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this
delay by pressing [#] + [0].
If E4 or E8 appears, more zones than the expansion units can handle have been programmed. Correct the programming
and then completely de-power and re-power the control to clear this indication and remove the disable indication.
✱
] and [#] both at once, within 50 seconds of powering up.
Procedure
Press [ ∗ ] + [Field Number], followed by the required entry.
When the desired field number appears, simply make the required entry. When the last
entry for a field is entered, the touchpad beeps three times and automatically displays
the next data field in sequence.
If the number of digits that you need to enter in a data field is less than the maximum
digits available (for example, the phone number fields *41, *42), enter the desired data,
then press [ ∗ ]. The entry is terminated and the next data field number appears.
Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
Press [ ∗ ] + [Field Number] + [ ∗ ]. (Applies only to fields ∗ 40–*43, *45, *94, and pager
programming fields)
Used to Program
Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800
RF transmitters.
Unlabeled touchpad keys (known as ABCD keys) for special functions
Same options as *56 mode, but with fewer prompts. Intended for those familiar with
this type of programming, otherwise *56 mode is recommended.
Assign module addresses and map individual relays/powerline carrier devices
4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers
Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
Zone alpha descriptors
– 2 –
✱
98 is used to exit programming