Initializing The E, F, 14, 19, 1E, 1F Page Data; Modification Of E, F, 14, 19, 1E, 1F Page Data - Sony HVR-Z1J Service Manual

Ver. 1.7 2007. 10
The changed portions from
Ver. 1.6 are shown in blue.
1-2-4. INITIALIZATION OF E, F, 14, 19, 1E, 1F PAGE DATA
Note1: There are the two modes, NTSC(60i) and PAL(50i), in each page
of E, F, 14, 19, 1E, and 1F.
These pages in NTSC(60i) mode and these pages in PAL(50i) mode
are independent completely. So, perform the initialization in both
modes.
When reading or writing these pages in NTSC(60i) mode, set the
NTSC(60i)/PAL(50i) switch (DB-018 board S201) to
"NTSC(60i)".
When reading or writing these pages in PAL(50i) mode, set the
NTSC(60i)/PAL(50i) switch to "PAL(50i)".
Note2: After completing the initialization, reset the NTSC(60i)/PAL(50i)
switch to the following position.
"NTSC(60i)" (HVR-Z1J/Z1U/Z1N), "PAL(50i)" (HVR-Z1E/Z1P/
Z1C)
Note3: When reading or writing the E, F page data, select page: 0, address:
10, and set data: 00.
When reading or writing the 14, 19, 1E and 1F page data, select
page: 0, address: 10, and set data: 01, then select 4, 9, E or F page.
The 14, 19, 1E or 1F page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
"00".
CPC lid
Screw (M2x4)
Order of Initialization:
[NTSC (60i) mode]
1) Set S201 to "NTSC (60i)".
2) Initializing the E, F, 14, 19, 1E, 1F Page Data (NTSC(60i)
mode)
3) Modification of E, F, 14, 19, 1E, 1F Page Data (NTSC(60i)
mode)
[PAL (50i) mode]
1) Set S201 to "PAL (50i)".
2) Initializing the E, F, 14, 19, 1E, 1F Page Data (PAL(50i) mode)
3) Modification of E, F, 14, 19, 1E, 1F Page Data (PAL(50i) mode)
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
S201
PAL (50i)
R
r
NTSC (60i)
Fig. 6-1-6.

1. Initializing the E, F, 14, 19, 1E, 1F Page Data

Note1: If "Initializing the E, F, 14, 19, 1E, 1F Page Data" is performed,
all data of the E page, F page, 14 page, 19 page, 1E page and 1F
page will be initialized. (It is impossible to initialize a single page.)
Note2: If the E, F, 14, 19, 1E, 1F page data has been initialized, following
adjustments need to be performed again.

1) Modification of E, F, 14, 19, 1E, 1F page data

2) Camera system adjustments
Note3: Perform this item in NTSC (60i) mode or PAL (50i) mode only
required.
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Initializing Method:
Order Page Address Data
1
2 0 01
3 0 10
4 6 01
5 6 03
6 6 02
7 6 01
8
6-17
E
00 to FF
F
10 to FF
14
00 to FF
19
00 to FF
1E
00 to E5
1F
00 to FF
Procedure
Set the NTSC(60i)/PAL(50i)
switch to the following position.
NTSC(60i) (NTSC(60i) mode)
PAL(50i) (PAL(50i) mode)
01 Set the data.
00 Set the data.
Set the following data, and press
PAUSE button.
2D (NTSC(60i)mode)
2F (PAL(50i)mode)
01 Set the data, and press PAUSE
button.
Check that the data changes to
"01".
00 Set the data, and press PAUSE
button.
Perform "Modification of E, F,
14, 19, 1E, 1F Page Data".