Sony HVR-Z1J Service Manual page 20

2
Note:
Be very careful not to
A
damage the flexible board.
A
4
3
1
1 Open the LCD section in the direction of the arrow.
2 Four screws (M2x4) black
3 Control switch block (ZS-5610) (6p)
4 Handle cabinet (Upper) assembly,
Control switch block (ZS-5610)
3
D
1
1 Peel off the harness fixed tape.
2 FP-984 flexible board (33P)
2
4
3 Four screws (M2x3) silver
4 EVF section
A B
Screw
Screw
M2x4 M2x6
3-080-203-51
3-080-203-31
C D
Bolt Screw
M2.6x5 M2x3
3-061-062-11 3-080-202-21
E F
Screw
Tipping screw
M2x5
M2x5
3-080-202-41
3-080-206-21
G
Silver
Screw
Black
M2.6x4
7-627-556-37
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
3
2
1
F
1 Four tipping screws (M2x5) black
2 Flexible flat cable (FDM-009) (10P)
3 Handle panel cabinet assembly,
FK-090 board, etc.
3
b
D
A
1 Turn over the hinge section in the
direction of the arrow a.
2 Four screws (M2x4) black
2
1
1 Hinge section, Harness (PD-226),
Harness (SW-116)
2 Harness (PD-226) (22P)
2-5
2. DISASSEMBLY
2. DISASSEMBLY
1
3
2
A
1 Close the LCD section in the direction of the arrow.
2 Two screws (M2x4) black
3 Hinge cover (Lower)
4
A Note:
upon assembling
Route the wire of the
harnesses without slack.
A
2
a
1
3 Two claws
4 Remove the p cabinet (C) assembly in
the direction of the arrow b.
Two claws
Remove the Hinge
cover (Rear) in the
direction of the arrow.
2
4
1 Two screws (M2x4) black
5
2 Two claws
3 Hinge cover (Front)
4 Hinge cover (Rear)
1
A
3
5 Hinge section, Harness (PD-226),
Harness (SW-116)
2
A
3
5
A 9
4
6
7
8
1
a
1 Open the LCD section in
the direction of the arrow a.
2 Peel off the protection sheet
(FP-967).
3 Two screws (M2x4) black
4 FP-967 board (6P)
5 Screw (M2x4) black
G
3
1
2
5
8
6
7
Note: Be very careful not to
damage the harnesses.
3
2
4
2-6
6
7
8
3
4
5
3
6 Harness (SW-116) (2P)
7 Harness (PD-226) (12P)
8 Harness (PD-226) (10P)
9 Harness guide. etc. @
1 Harness (PD-226), Harness (SW-116)
2 FP-967 board, Harness guide
3 Three screws (M2.6x4) silver
4 LCD section
4
1 Remove the harness (PD-226)
in the direction of the arrow.
2 Harness (SW-116) (2P)
3 Harness (PD-226),
Harness (SW-116), Harness clamp
4 Hinge section
5 Tape (W)
1
6 Harness clamp
7 Harness (PD-226)
8 Harness (SW-116)