Precautions On Adjusting - Sony HVR-Z1J Service Manual

Ver. 1.7 2007. 10
3-1-2.

Precautions on Adjusting

Note1:Before performing the adjustments, check the data of page: 0,
address: 10 is "00". If not, set data: 00 to this address.
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR" or set
the "Forced VTR Power ON mode" using the adjusting remote
commander (Note2).
To set to the camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the adjusting
remote commander (Note3).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note5)
2) The handle block (LCD block, EVF block, microphone unit
and VTR function switches) need not be connected. (Use the
adjustment remote commander, to operate the VTR block.) To
remove it, disconnect the following connectors.
IF-122 board CN305 (40P, 0.4mm)
(Or VC-367 board CN0008 (39P, 0.3mm)
FP-980 flexible CN802 (40P, 0.4mm)
(Or VC-367 board CN6001 (39P, 0.3mm)
3) The cabinet (L) block (Control switch block (PS5610)) must
be assembled for connecting the adjusting remote commander.
To remove it, disconnect the following connector.
VA-119 board CN2007 (18P, 0.5mm)
4) The JK-275 board must be assembled for connecting the
monitor TV. To remove it, disconnect the following connector.
VA-119 board CN2006 (22P, 0.5mm)
5) The XLR connectors need not be connected. (Except for "Audio
System Adjustment")
To remove it disconnect the following connector.
VA-119 board CN2005 (10P, 0.5mm)
6) The lens block (CD-522 board, SE-150 board) need not be
connected. To remove it, disconnect the following connectors.
VC-367 board CN1501 (51P, 0.3mm)
VC-367 board CN1502 (27P, 0.3mm)
VC-367 board CN1503 (10P, 0.5mm)
VC-367 board CN1001 (100P, 0.4mm)
7) The cabinet (R) block need not be connected. To remove it,
disconnect the following connector.
CK-143 board CN208 (32P, 0.5mm)
(Or VC-367 board CN0004 (33P, 0.3mm)
8) The battery terminal need not be connected. To remove them,
disconnect the following connector.
DB-018 board CN204 (4P, 1.5mm)
9) The FP-959 flexible (lithium battery) need not be connected.
But removing FP-959 flexible (removing DB-018 board
CN207) means removing the lithium 3V power supply (FP-
959 flexible, BT591), data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the cabinet (R)
block has been removed. (Refer to "6-4.Service Mode" for the
data on the history use and the self-diagnosis data.)
To remove the FP-959 flexible, disconnect the following
connector.
DB-018 board CN207 (6P, 0.5mm)
10) To open the DB-018 board, use the following extension cable
between the DB-018 board CN205 and DA-033 board CN104.
(J-6082-566-A) (28P 0.8mm)
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Note2: Setting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 02, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the VTR power to be turned on
with the control switch block (PS5610) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note3: Setting the "Forced Camera Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 01, and press the PAUSE
button of the adjusting remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS5610) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 00, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 0, address: 01, and set data: 0
Note5: Perform these adjustments of all in NTSC (60i) mode first, and
then perform these adjustments of all in PAL (50i) mode.
6-116