Lv Standard Data Input (Ntsc (60I) & Pal (50I) Modes); Auto White Balance Adjustment; (Ntsc (60I) & Pal (50I) Modes); Auto White Balance Adjustment Nd Off - Sony HVR-Z1J Service Manual

Ver. 1.7 2007. 10
16. LV Standard Data Input
(NTSC (60i) & PAL (50i) modes)
Note1: Perform these adjustments of all in NTSC (60i) mode first, and
then perform these adjustments of all in PAL (50i) mode.
Adjust the normal coefficient of the light value.
Subject
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note2: This adjustment should be carried out upon completion of "Auto
White Balance Standard Data Input".
Note3: The data of page: 0, address: 10 must be "00".
Note4: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Note5: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Switch setting:
1) REC FORMAT (IN/OUT REC menu) .................. HDV1080i
(Page: 6, Address: 9B, Bit2=0)
2) ND FILTER ...................................................................... OFF
(Page: 6, Address: 9B, Bit4=0, Bit5=0)
3) STEADY SHOT (CAMERA SET menu) ........................ OFF
4) FOCUS .................................................................. MANUAL
5) ZOOM ........................................................................ LEVER
Adjusting method:
Order Page Address Data
1
2 0 01
3 6 30
4 6 C9
5 6 01
6 6 02
7 0 03
8 1
Note6: The adjustment data will be automatically input to page: F, address:
1A, 1B.
Note7: If it isn't satisfied, repeat the adjustment again.
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 6 30
3 6 C9
4 0 03
5 0 01
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Clear chart
(HD color bar standard picture frame)
Display data of page 1 (Note4)
Adjustment remote commander
F
1A, 1B
0FE0 to 1020
Display data
Procedure
Check the picture frame.
Refer to "10. Picture Frame
Setting".)
01 Set the data.
01 Set the data.
10 Set the data.
0D Set the data, and press PAUSE
button.
Check that the data changes to
"01". (Note6)
1E Set the data.
Check that the display data
(Note5) satisfies the specified
value. (Note7)
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.
00 Set the data.
00 Set the data.

17. Auto White Balance Adjustment

(NTSC (60i) & PAL (50i) modes)
Note: Perform these adjustments of all in NTSC (60i) mode first, and
then perform these adjustments of all in PAL (50i) mode.

17-1. Auto White Balance Adjustment ND OFF

Adjust to the proper auto white balance output data when the ND
filter switch is "OFF".
If it is not correct, auto white balance and color reproducibility will
be poor.
Subject
Filter
Adjustment Page
Adjustment Address
Note1: The data of page: 0, address: 10 must be "00".
Note2: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) REC FORMAT (IN/OUT REC menu) .................. HDV1080i
(Page: 6, Address: 9B, Bit2=0)
2) ND FILTER ...................................................................... OFF
(Page: 6, Address: 9B, Bit4=0, Bit5=0)
3) FOCUS .................................................................. MANUAL
4) ZOOM ........................................................................ LEVER
Adjusting method:
Order Page Address Data
1
2 0 01
3 F 3C
4 F 3D
5 F 3E
6 F 3F
7 6 01
8 6 01
9 6 02
Note3: The adjustment data will be automatically input to page: F, address:
40 to 43.
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 0 01
3
6-38
Clear chart
(HD color bar standard picture frame)
Filter C14 for color temperature
correction
F
3C to 3F, 40 to 43
Procedure
Place the C14 filter for color
temperature correction on the
lens.
01 Set the data.
2B Set the data, and press PAUSE
button.
E0 Set the data, and press PAUSE
button.
58 Set the data, and press PAUSE
button.
78 Set the data, and press PAUSE
button.
83 Set the data, and press PAUSE
button.
81 Set the data, and press PAUSE
button.
Check that the data changes to
"01". (Note3)
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
Remove the C14 filter.