Epson AcuLaser CX11 Service Manual page 640

EPSON AcuLaser CX11/CX11F
Maintenance
Code
Label
Main Sub
LIN_DIALTONE_DETECT_TIME 300
LIN_RING_DETECT_TIME 300
LIN_ONHOOK_DETECT_TIME 300
LIN_DIALTONE_DETECTION 300
LIN_DIALTONE_FREQ 300
LIN_BUSYTONE_FREQ 300
LIN_BUSYTONE_PATTERN 300
LIN_NCU_TYPE 300
LIN_20PPS_ENABLE 300
LIN_DP_RELAY_DELAY 300
LIN_DIAL_NG_NUMBER 300
LIN_RING_INVALID_TIME 300
APPENDIX
Table 7-18. List of System Parameter (Phone Line)
User Internal
Access Address
--- Dial tone detecting time out
027 05F
--- Ring detecting time
030 060
The time from detecting ring until it is judged as dialing
--- Off-hook detection time
031 061
Time limit for attached phone off-hook condition to regard it as a
shut-off signal
--- Enables or disables detection of dial tone
032 062
Select whether detect or not detect dial tone immediately after
detecting off-hook condition when the line type is set to PSTN.
When this is set to "disable", blind dialing is perfomed.
--- Dial tone frequency
033 063
--- Busy tone frequency
034 064
--- Busy tone pattern
035 065
--- NCU type
036 066
--- Enables or disables 20 PPS setting
037 067
When this is set to "disable", 20 PPS setting specified in the dial
type setting (300-001) becomes invalid.
--- Waiting time until the line stabilizes when performing pulse dialing 0 to 2550 ms (1 setp = 10 ms)
038 068
--- Allows or not allows to store emergency phone number into the
039 069
speed-dial memory
Emergency phone number: XXXXX
--- Time for judging ring signal is OFF
040 06A
The time limit for ring signal. The line is shut-off if the time exceeds
the set value.
Description
Fax Unit System
manuals4you.com manuals4you.com
Setting Value
0 to 255 sec (1 step = 1 sec)
100 to 2550 ms (1 step = 10 ms)
200 to 5100 ms (1 step = 20 ms)
0 = Enable (detect)
1 = Disable (not detect)
0 = 350 to 450Hz
1 = 300 to 500Hz
2 = 450 to 650Hz
0 = 400Hz
1 = 350 to 450Hz
2 = 300 to 500Hz
3 = 450 to 650Hz
~
0 = ON 0.30 0.80S
~
OFF 0.30 0.80S
~
1 = ON 0.20 0.60S
~
OFF 0.30 0.60S
~
2 = ON 0.50 1S
~
OFF 0.50 1S
~
3 = ON 0.12 1.2S
~
OFF 0.12 1.2S
0 = For Japan
0 = Enable
1 = Disable
0 = Allows
1 = Not allows
0 to 2550 ms (1 step = 10 ms)
0 = 125 ms
Revision B
Default Remarks
20 seconds ---
(20)
---
180ms
(18)
---
1300ms
(65)
Disable ---
(1)
---
400Hz
(0)
---
400Hz
(0)
---
(0)
Not used
(0)
Enable ---
(0)
---
10ms
(1)
Allows Fixed to 0
(0) Not used
---
125ms
(0)
642