Operation; Using The On-Screen Menus - Runco D-73d Ultra Installation & Operation Manual

To display the Main Menu, press the MENU button on the remote control or Dimension
Digital Controller front panel.
To select a menu item, use the
Digital Controller front panel to highlight it. Then, to confirm your selection, press
ENTER on the remote control or Dimension Digital Controller front panel.
The D-73d OSD menus are arranged hierarchically, as shown in Figure 4-1. Some
menu options apply only to certain input signal types. For example, Phase and Tracking
can only be adjusted for RGB, Component video or SCART signals.
Composite 1
Composite 2
Composite 3
Component
Input Source
HD 1
HD 2
SCART
DisplayPort
16:9
4:3
Letterbox
VirtualWide
Aspect Ratio
Cinema
Virtual Cinema
Native
Auto Cinema
Screen
Screen 1 / Screen 2
Brightness
Contrast
Color
Picture
Tint
Sharpness
Noise Filter
Left/Right
Up/Down
Width
Height
Overscan
Input
Overscan Mode
(Zoom/Crop)
Position
Phase
(RGB/Component/SCART signals
only)
Tracking
(RGB/Component/SCART signals
only)
Recall ISF Night or ISF Day
Memory
Recall/Save Custom 1 or Custom 2
Presets
Reset Custom 1 and Custom 2 to
Factory Default
3D Mode
3D
(Auto, Off, Side-by-Side,
Top-and-Bottom or Frame Packing)
Processing
Reverse Eyes
(On/Off)
Off, 30 Minutes, 60 Minutes, 90
Sleep Timer
Minutes, 2 Hours or 4 Hours
Signal
System
Information
Network
Field Service
Manufacturing
Figure 4-1. D-73d OSD Menu Structure
D-73d Series Installation/Operation Manual
and buttons on the remote control or Dimension
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
HDMI 6
HDMI 7
HDMI 8
Calibration
(read-only)
Note: Default settings appear in bold type.
Gain
Offset
Gamma
Display Color -
Common Settings
Color Temp
Color Gamut
PCE
SatCo
Display Color -
ConstantContrast
Projector Settings
Engine Configuration
Brightness
Contrast
Input Image Color
Tint
Sharpness
Gain
Offset
Input Color
Chroma Delay
Noise Filter
Save ISF Night
Back / Confirm
Save ISF Day
Memory Preset
Copy/Paste
Aspect Ratio
Left/Right
Up/Down
Width
Output Shift
Height
Screen Masking
Corner Alignment
Image Alignment
Midpoint Alignment
Both, Primary or
Adjustment Mode
Secondary
Owner Name
ISF Calibrated
Splash Configure ISF Other
Splash Timer
Splash Enable
OSD Position Hor. / Ver.
65

4. Operation

4.1
Using the On-Screen
Menus
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35 or 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Simple (5500K, 6500K, 7500K or 9300K)
Auto, REC709, SMPTE-C, EBU, Native or PCE
Hue (Red / Yellow / Green / Cyan / Blue / Magenta)
Saturation (Red / Yellow / Green / Cyan / Blue /
Magenta)
Level (Red / Yellow / Green / Cyan / Blue / Magenta)
Runco Smart Color (RSC) (On or Off)
White Balance (Red / Green / Blue Gain)
On or Off
Low, Medium, High or Off
Dual / Single
-50, -49 ... 0 ... 49, 50
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
0, 1, 2 ... 7
(Composite inputs only)
0, 1, 2 ... 63
Copy Settings
Paste Settings
Copy Settings
Paste Settings
-50, -49 ... 0 ... 49, 50
-50, -49, 48 ... 0
0, 1, 2 ... 100
(Top / Bottom / Left / Right / Test Pattern Enable)
Top Left / Top Right / Bottom Left / Bottom Right /
Test Pattern Enable
Center / Top Middle / Left Middle / Right Middle /
Bottom Middle / Test Pattern Enable
5, 6, 7 ... 15 ... 59, 60
On/Off
0, 1, 2 ... 100