Maytag MLE20PRBZW1 Installation Instructions Manual page 38

ELECTRONIC CONTROL SETUP INSTRUCTIONS
Code Explanation
H. 01 SUPER CYCLE UPGRADE PRICE (WASHER)
(Skipped unless Super Cycle pricing is enabled.)
H. 01 This represents the number of coin 1 required to
upgrade a base cycle to a super cycle.
• Advance from 0-39 by pressing the
lower-left (PERM. PRESS) button.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
h. 01 SUPER CYCLE TYPE (WASHER}
(Skipped unless Super Cycle pricing is enabled.)
h. 01 This represents the Super Cycle upgrade option.
Press the lower-left (PERM. PRESS) button
to step through upgrade options 1 through
3 as follows:
01 - enhanced wash, extra 3 minutes
of wash tumble in addition to the
programmed wash time.
02 - extra rinse for all cycles.
03 - both 01 and 02.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
J. Cd PAYMENT MODE (COIN/DEBIT OPTION)
J. Cd Both coin and debit selected. Press the lower-right
(QUICK CYCLE) button 3 consecutive times to
change this selection.
Coins selected, debit disabled. Press the lower-
right (QUICK CYCLE) button 3 consecutive times
to change this selection.
PR models: Factory default to J._d. Debit Card
selected, coins disabled. Press the lower-right
(QUICK CYCLE) button 3 consecutive times to
change this selection.
Enhanced Debit is self-selected when a Generation
2 card reader is installed in the washer/dryer.
The Ed option cannot be manually selected or
deselected.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
J, C
J, d
J. Ed
L. 00
L. 00
L. PS
n. CE
n. 00
n. CE
PRICE SUPPRESSION OPTION
This option causes the customer display to show
"ADD" or "AVAILABLE" rather than the amount of
money to add. (Used mainly in debit installations.)
Not Selected "00."
Selected "PS."
Press the lower-right (QUICK CYCLE) button
once to change this selection.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
CLEAR ESCROW OPTION
When selected, money held in escrow for 30
minutes without further escrow or cycle activity will
be cleared.
Not Selected "00."
Selected "CE."
Press the lower-right (QUICK CYCLE) button
once to change this selection.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
Code Explanation
r. 800 TOP SPIN SPEED RPM (WASHER)
r. 800
This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm.
Step between speeds by pressing the lower-left
(PERM. PRESS) button. Factory default of 800
rpm.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
U. 00 PENNY INCREMENT OFFSET (WASHER)
U. 00 This represents the penny increment price offset
used in Generation 2 (Enhanced Debit) PR models.
Choose from 0-4 pennies by pressing the lower-
left (PERM. PRESS) button.
• Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
U.00 PENNY INCREMENT OFFSET (DRYER}
U.00 This represents the penny increment price offset
used in Generation 2 (Enhanced Debit) PR models.
Choose from 0-4 pennies by pressing the upper-
left (WHITES & COLORS) button.
• Press the lower-middle (DELICATES AND KNITS)
button once to advance to next code.
A1.00 PREWASH LENGTH (WASHER)
A1.00 This is the number of minutes of PREWASH.
Choose 00 to disable the prewash or select
between 2 and 7 minutes by pressing the lower-left
(PERM. PRESS) button.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
A2.03 FINAL SPIN LENGTH (WASHER)
A2.03
This is the number of minutes of final high
speed spin. Choose from 03-08 minutes by
pressing the lower-left (PERM. PRESS) button.
Press the lower-middle (DELICATES AND
KNITS) button once to advance to next code.
END of SET-UP PROCEDURES.
EXIT FROM SET-UP MODE
PD Models: Turn service switch key clockwise and remove it.
PR Models: Remove manual set-up card.
38