Power Supply Removal Instructions - Alcatel OMNISWITCH 8800 Getting Started Manual

Power Supply Removal Instructions

1 Loosen the four captive screws, located at the four
corners of the power supply's front panel. If necessary,
use a flat-blade screwdriver to loosen the screws. Be sure
that all captive screws are completely disengaged from the
threaded holes in the chassis before continuing.
Note. Alcatel provides factory-installed blank cover plates
for empty module slots. Do not remove these cover plates
as they play an important role in chassis ventilation.
6 Installing the Hardware
O K
1
O K
2
T E
M P
F A
IL
D C
O K
A C
O K
C A
W IT U T
H FO IO
TH E RI N :
AL UR TH
SE L PO SK PO IS
RV W ER OF W ER UN !
IC IN EL EC IT M AY
G SU TR SU PP
UN PP LY IC AL LI E BE
IT. CO CO EQ
RD SH RD UI PP
S BE OC S. ED
K, DI SC TO
FO RE
RE ON DU
NE CE A T
CT T E
PL
PR US N T
EV D' UN IO
TO US EN CO N :
FA LE IR RD CE
IR E LA S CO LE S CH ON T AP
D' AL PA
RE RD OC RE
PA RA ON S EL IM EN IL CO
TI ON S D' EC TA M PO
AL TR TI ON
. IM EN IQ . AF RT E
TA UE S,
TI ON DE IN DE
AV BR
AN AN
TE CH
DE E
C A
W IT U T
H FO IO
TH E RI N :
AL UR TH
SE L PO SK PO IS
RV W ER OF W ER UN
IC IN EL EC SU IT M AY
G SU TR PP
UN PP LY IC AL LI E BE
IT. CO CO EQ
RD SH RD UI PP
S BE OC S. ED
K, DI SC TO
FO RE RE
ON D
NE
2 3
0 V
5 0
/6 0
H z
, 8
.0
A
2 3
0 V
5 0
/6 0
H z
, 8
.0
A
2
With one hand, grasp the handle at the front of the
power supply and slowly pull the power supply out of the
power supply bay. Do not pull the power supply
completely out of the bay with one hand.
CA
WI UT
TH TH FO IO N:
AL E RIS UR TH
SE L PO K OF PO IS UN
RV ICI WE R SU EL WE R SU IT !
NG EC TR PP MA Y BE
UN PP LY ICA LIE
IT. CO L SH CO EQ UIP
RD S BE OC RD S. PE
K, DIS TO D
FO RE CO RE DU
NN CE
EC T
23
0V
50
/6 0H
z, 8. 0
A
3
When the power supply is pulled out far enough (about
10 inches), place your other hand under the power supply
casing to support its weight.
4
Continue pulling the power supply out until it is
removed from the chassis.
5
Set the power supply aside on a clean, static-free
surface. You will need to re-install it later.
6
Remove all remaining power supplies by repeating
steps 1 through 5.
7
Continue to "Lifting the Chassis" on page
O K
1
O K
2
T E
M P
F A
IL
D C
O K
A C
O K
CA UT
WI TH IO
TH E RIS FO N:
AL L PO UR TH
SE RV WE K OF PO WE IS UN
ICI R SU EL R SU IT MA
NG EC PP TR PP Y BE
UN IT. LY ICA LIE EQ
CO L SH RD CO RD UIP
S BE OC K, S. PE
FO DIS TO D
RE CO RE D
NN E
AT TE
PL US NT
PR EV D'U IO
TO EN N CO N:
FA US IRE LE IR LE RD CE T AP
LA S CO S CH ON PA
RE RD OC D'A RE
PA RA ON S EL LIM EN CO IL
TIO S D'A EC TA MP
N. LIM TR IQ TIO N. OR TE
EN TA UE AF
TIO S, DE IN DE
N AV BR AN
AN TE CH
DE E
23
0V
50 /6 0H
z,
8. 0
A
7.
March 2005