Zoom B3 Operation Manual page 42

Effect Types and Parameters
060 StereoCho This is a stereo chorus with a clear tone.
061 Ensemble
062 VinFLNGR
063 Flanger
064 DynaFLNGR
065 Vibrato
066 Octave
42
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
LoCut Off–800Hz
Page02
Specifies the low-range cutoff point
for the effect sound.
This is a chorus ensemble that features three-dimensional movement.
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
Tone 0–10
Page02
Adjusts the tone.
This analog flanger sound is similar to an MXR M-117R.
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
PreD 0–50
Page02
Sets pre-delay time of effect sound.
LoCut Off–800Hz
Page03
Sets the cut-off frequency in the low
range of the effect sound.
This is a jet sound like an ADA flanger.
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
PreD 0–50
Page02
Sets pre-delay time of effect sound.
LoCut Off–800Hz
Page03
Sets the cut-off frequency in the low
range of the effect sound.
The volume of the effect sound changes according to the input signal level with this
dynamic flanger.
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
Reso -10–-1, 0, 1–10
Page02
Adjusts the intensity of the modulation
resonance.
This effect automatically adds vibrato.
Knob1
Depth 0–100
Page01
Sets the depth of the modulation.
Tone 0–10
Page02
Adjusts the tone.
This effect adds sound one octave below the original sound.
Knob1
Oct 0–100
Page01
Adjusts the level of the one-octave
lower sound component.
Low 0–10
Page02
Adjusts the low frequency level.
Knob2
Rate 1–50
Sets the speed of the modulation.
Level 0–150
Adjusts the output level.
Knob2
Rate 1–50
Sets the speed of the modulation.
Level 0–150
Adjusts the output level.
Knob2
Rate 0–50
Sets the speed of the modulation.
Mix 0–100
Adjusts the amount of effected sound
that is mixed with the original sound.
Knob2
Rate 0–50
Sets the speed of the modulation.
Mix 0–100
Adjusts the amount of effected sound
that is mixed with the original sound.
Knob2
Rate 0–50
Sets the speed of the modulation.
Level 0–150
Adjusts the output level.
Knob2
Rate 0–50
Sets the speed of the modulation.
Level 0–150
Adjusts the output level.
Knob2
P Dry 0–100
Adjusts the level of the original sound.
Mid 0–10
Adjusts the middle frequency level.
Knob3
Mix 0–100
Adjusts the amount of effected sound
that is mixed with the original sound.
Knob3
Mix 0–100
Adjusts the amount of effected sound
that is mixed with the original sound.
Knob3
P Reso -10–-1, 0,1–10
Adjusts the intensity of the modulation
resonance.
Level 0–150
Adjusts the output level.
Knob3
P Reso -10–-1, 0,1–10
Adjusts the intensity of the modulation
resonance.
Level 0–150
Adjusts the output level.
Knob3
P Sense -10–-1, 1–10
Adjusts the sensitivity of the effect.
Knob3
P Bal 0–100
Adjusts the balance between original
and effect sounds.
Knob3
Tone 0–10
Adjusts the tonal quality of the one-
octave lower sound component.
Level 0–150
Adjusts the output level.
P
P