Zoom B3 Operation Manual page 34

Effect Types and Parameters
006 Limiter
007 SlowATTCK This effect slows the attack of each note, resulting in a violin-like performance.
008 ZNR
009 GraphicEQ This unit has a seven band equalizer.
010 ParaEQ
011 Splitter
012 Bottom B
013 Exciter
34
This is a limiter that suppresses signal peaks above a certain reference level.
Knob1
THRSH 0–50
Page01
Adjusts the reference signal level for
the limiter action.
REL 1–10
Adjusts the delay between the point
Page02
where the signal level falls below the
threshold level and the limiter release.
Knob1
Time 1–50
Page01
Adjusts the attack time.
ZOOM's unique noise reduction cuts noise during pauses in playing without affecting the tone.
Knob1
THRSH 1–25
Page01
Adjusts the effect sensitivity.
Knob1
50Hz -12–12
Page01
Adjusts the amount of boost/cut at 50
Hz.
500Hz -12–12
Page02
Adjusts the amount of boost/cut at
500 Hz.
10kHz -12–12
Page03
Adjusts the amount of boost/cut at
10 kHz.
This is a 2-band parametric equalizer.
Knob1
Freq1 20Hz–20kHz
Page01
Adjusts center frequency of EQ1.
Freq2 20Hz–20kHz
Page02
Adjusts center frequency of EQ2.
Level 0–150
Page03
Adjusts the output level.
This effect divides the signal into two bands (high/low) and lets you freely adjust the mix
ratio of the two bands.
Knob1
Hi 0–100
Page01
Adjusts the mix ratio of the high
frequency band.
Level 0–150
Page02
Adjusts the output level.
Emphasizes the low and high frequencies.
Knob1
Bass 0–10
Page01
Adjusts the amount of low-frequency
boost.
This exciter is in the style of the BBE Sonic Maximizer.
Knob1
Bass 0–10
Page01
Adjusts the amount of low-frequency
phase correction.
Knob2
P Ratio 1–10
Adjusts the compression ratio of the
limiter.
Knob2
P Curve 0–10
Set the curve of volume change during
attack.
Knob2
P DETCT GtrIn, EfxIn
Sets control signal detected.
Knob2
120Hz -12–12
Adjusts the amount of boost/cut at
120 Hz.
800Hz -12–12
Adjusts the amount of boost/cut at
800 Hz.
Level 0–150
Adjusts the output level.
Knob2
Q1 0.5, 1, 2, 4, 8, 16
Adjusts EQ1 Q.
Q2 0.5, 1, 2, 4, 8, 16
Adjusts EQ2 Q.
Knob2
Lo 0–100
Adjusts the mix ratio of the low
frequency band.
P
Knob2
P Trebl 0–10
Adjusts the amount of high-frequency
boost.
Knob2
P Trebl 0–10
Adjusts the amount of high-frequency
phase correction.
Knob3
Level 0–150
Adjusts the output level.
Knob3
Level 0–150
Adjusts the output level.
Knob3
Level 0–150
Adjusts the output level.
Knob3
400Hz -12–12
Adjusts the amount of boost/cut at
400 Hz.
4.5kHz -12–12
Adjusts the amount of boost/cut at
4.5 kHz
Knob3
Gain1 -20–20
Adjusts EQ1 gain.
Gain2 -20–20
Adjusts EQ2 gain.
Knob3
Freq 80Hz–2.5kHz
Adjusts the crossover point between the
high frequency and low frequency band.
Knob3
Level 0–150
Adjusts the output level.
Knob3
Level 0–150
Adjusts the output level.