Table of Contents
Advertisement
Upon setup of the previous "Chain Play List," select the desired mode in the "Chain Play MD?" (Setup
of the chain play mode) menu in the same SETUP mode.
<Important>: Be sure the Chain Play List is set up correctly before setting the chain play mode. Each
setting of the chain play mode except " Off ," will not function if the previously mentioned " Chain play
list " is not set up correctly beforehand. If the mode is executed while set up of with an incorrect list,
after displaying " Illegal P.List! ," the D2424LVmkII will automatically go to the previously mentioned
" Chain Play List? " menu.
<Note>: The chain play mode setting will be held even though power is switched off, and if power is
switched when the D2424LVmkII is set to pause mode, the recorder will automatically execute chain
play. If chain play is no longer required, reset to " Off" the " Chain Play? " menu after ending chain
play.
(1)
Press the [SETUP] key while the D2424LVmkII is
in the stop mode to switch to the SETUP display.
(2)
Display the "Chain Play MD?" menu via the Jog
dial and then press the [EXECUTE/YES] key.
The recorder will change to the display for setting
up of the chain play mode and the present setup
mode will flash (In the initial setup, "Off" will flash).
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
4
5
6
7
8
9
3
10
(3)
Select the desired mode via the Jog dial.
When the Jog dial is rotated, modes other than the
currently shown "Off" listed below can be selected.
"Off"
"Pause" (Pause mode)
"Auto P" (Auto play mode)
"Rpt" (Pepeat mode)
(4)
Press the [EXECUTE/YES] key after selecting the
mode.
The recorder will exit from the SETUP mode after
setup is completed.
In this step, if it was completed in the setup other
than the "Off" mode, the D2424LVmkII will
automatically locate to the "AUTO RTN START point"
of the first program in the previously setup "Chain
list" and stop.
If it was completed after setup to "Off," the
D2424LVmkII will return to the first display of the
program prior to entering the SETUP mode.).
Model D2424LVmkII Reference Manual (Chain Play function)
Setup of the Chain Play Mode
OL
BIT
0
3
6
9
12
18
CLOCK
24
30
42
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
OL
24
BIT
0
3
6
9
12
18
CLOCK
24
30
42
21
24
11
12
13
14
15
16
17
18
19
20
22
23
Refer to previous page
61 on the function of
each mode.
If the D2424LVmkII is played back after this, func-
tions of the mode selected will be executed from
the first program in the chain list.
Normally, in chain play as explained above, execu-
tion starts from the first program on the chain list
but any program of your choice can be specified
and chain play executed from that program.
For details, refer to "Specify the program and execute
chain play".
<The "Current" display after setup>
24
FS
If the "Chain Play?" menu is set to other
kHz
INT
than "Off" ("Pause," "Auto P" or "Rpt"), then
exit from the SETUP mode, the current dis-
play will change as shown in example be-
low and, the display will be different from
when it is set to "Off."
FS
kHz
INT
<When "Chain Play?" is set to other than "Off.">
The above is an example showing that pro-
gram 03 (P03) activated by the ABS time
base, is set at fourth in the chain list.
As shown here, when the chain list is cor-
rectly setup and the "Chain Play?" menu
set to other than "Off," in which order (For
example, "c04") of the chain list had the
presently active program been setup, will
be indicated. Should it be changed to an-
other time base, the chain list number will
be indicated in the same manner.
63
<When "Chain Play?" is set to "Off.">
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
ABS
M
S
F
PGM
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
20
21
22
23
24
ABS
M
S
F
PGM
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
20
21
22
23
24
Advertisement
Chapters
Table of Contents
