Table of Contents
Advertisement
APPENDIX
(Operation manual for the recorder with the Model 8346 TC/SYNC card installed)
<How to record time code>
After setting the time code recording mode de-
scribed above, record time code by the follow-
ing procedure.
1. Press the [EDIT] key while holding down the [SHIFT]
key to turn TC READY on (the TC READY indicator
will flash).
2. Press the [PLAY] button while holding down the
[RECORD] button (the TC READY indicator will light).
Unlike audio signal recording, you do not need
to arm a track for time code.
Also note that recording time code does not con-
sume the hard disk space.
To erase all the time code information, see "Eras-
ing the recorded time code" described later.
Editing the internal generator time code
Editing the internal generator time code can be done
only when the time code recording mode (described
above) is set to "Free Run".
1.
Select "Gen TC Set" of the Generator Setup mode
and press the [EXECUTE/YES] key.
The current internal generator time code is
displayed and you are now ready to edit the time.
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
2.
Use the Shuttle dial to move the editing point
(which is flashing), and use the Jog dial to set the
numeric value.
Up to 23H 59M 59S **F (** = current frame rate - 1)
can be set.
3.
After editing is completed, press the
[EXECUTE/YES] key.
Force jamming to external time code
Force jamming to external time code can be done
only when the time code recording mode (described
above) is set to "Free Run". Note that the following
description assumes that the 8346 is receiving ex-
ternal time code.
1.
Select "Force JAM" ("SURE?" flashes) of the
Generator Setup mode and press the
[EXECUTE/YES] key.
The force jamming to the external time code starts
and the display shows the time code value in
realtime.
GEN
H
M
S
F
OL
24
BIT
0
3
6
9
12
18
CLOCK
24
INT
30
42
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
GEN
H
M
S
F
OL
24
BIT
0
3
6
9
12
18
CLOCK
24
INT
30
42
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
If the 8346 does not receive external time code cor-
rectly, the warning message "Void LTC In!" appears
when pressing the [EXECUTE/YES] key.
Selecting the output time code
When the time code recording mode (described
above) is set to "Free Run" or "24H Run", the 8346
can output the internal generator time code or re-
corded time code. Note that it does not output time
code when the time code recording mode is set to
"Rec Run" or "Ext Run".
<CAUTION>
• While time code is output, the recorder's vari pitch
and word sync functions are prohibited.
Note that the time code output setting is available
only when an " Async" mode (" adat: Async " or
" SPDIF: Async ") is selected in the " D. in? " menu of the
Setup mode.
Also note that if you execute a program change, etc.
the generator stops time code generation.
• The " TC Out Sel? " setting returns to the default
SF
" Repro " when turning the power off.
FS
kHz
1.
Select "TC Out Sel?" ("?" flashes) of the Generator
Setup mode and press the [EXECUTE/YES] key.
The current output setting flashes (the default
setting is "Repro").
SF
FS
kHz
2.
Use the Jog dial to select "Repro" or "Gen.".
The time code output from the [TIME CODE OUT]
terminal changes according to the setting.
3.
After the setting is completed, press the
[EXECUTE/YES] key.
4.
Press the [EXIT/NO] key (or the [STOP] button) to
exit the Generator Setup mode.
8
Flashing
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
11
17
18
20
10
12
13
14
15
16
19
Reproduced time code
Internal generator time code
GEN
H
M
S
F
SF
OL
BIT
24
0
3
FS
6
9
kHz
12
CLOCK
18
24
INT
30
42
20
21
22
23
24
GEN
H
M
S
F
SF
OL
BIT
24
0
3
FS
6
9
kHz
12
CLOCK
18
24
INT
30
42
21
22
23
24
Flashing
GEN
H
M
S
F
SF
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
21
22
23
24
Advertisement
Chapters
Table of Contents
