Table of Contents
Advertisement
Model D2424LVmkII Reference Manual (Changing the Initial Settings <SETUP mode>)
Pressing the [EXECUTE/YES] key to turn off the
flashing "?" character. The Offset mode indicator
flashes. With the initial setting, "ABS" flashes as
shown below.
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
(3)
Use the Jog dial to select the desired Offset mode.
Rotating the Jog dial clockwise or counter-clockwise
will alternately show a flashing "ABS" and "Bar ".
If you select "ABS", the specified MTC offset time is
output at ABS 00H 00M 00S 00F.
If you select "Bar ", the specified MTC offset time
is output at 001bar 1beat 00clk of the Tempo Map.
(4)
Press the [EXECUTE/YES] key.
The selected offset mode is stored and the display
returns to the indication with flashing "?".
To cancel the setting operation, or to exit SETUP
mode after storing data, press the [STOP] button
or the [EXIT/NO] key. Each time you press one of
these keys, the recorder returns to the previous
hierarchy level of the menu, and finally exits
SETUP mode.
Setting the Slave type
The "Setting the Slave type" menu enables you to setup
how recorder should function after chase lock, when
recorder is set to sync externally in "slave mode ON"
by the previously mentioned "Setting the slave mode."
• Initial setting:
• Option:
* You can set the parameter for each Program
individually.
* The settings can be saved and loaded as part of the
song data.
* The settings are maintained after you turn off the
power to the recorder.
* The Program is automatically checked before the
operation.
* The sampling rate is automatically checked before
the operation.
(1)
While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
(2)
Turn the Jog dial to select "Slave Type ?" ("?"
flashes.), then press the [EXECUTE/YES] key.
The current Slave type appears on the display.
Pressing the [EXECUTE/YES] key turns off the
flashing "?" character, and the Slave type indicator
flashes. With the initial setting, "Vari" flashes as
shown below.
OL
BIT
24
0
3
FS
6
9
kHz
12
CLOCK
18
24
INT
30
42
18
20
21
22
23
24
11
12
13
14
15
16
17
19
Flashing
OL
24
BIT
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
11
12
13
14
15
16
17
18
19
20
21
22
23
24
[Vari]
[Vari], [Free], [Once]
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
(3)
Use the Jog dial to select the desired Slave type,
and press the [EXECUTE/YES] key.
Rotating the Jog dial clockwise and counter-
clockwise will cause the "Vari", "Free" and "Once"
indicators to flash in sequence.
Vari
(Default)
Free
Once
(4)
Press the [EXECUTE/YES] key.
The selected Slave type is stored, and "?" flashes.
To cancel the setting operation, or to exit SETUP
mode after storing data, press the [STOP] button
or the [EXIT/NO] key. Each time you press one of
these keys, the recorder returns to the previous
hierarchy level of the menu, and finally exits
SETUP mode.
<Note>:
external device to the recorder with any Slave
type.
<Note>:
Pitch function is automatically disabled. (The
" VARI PITCH " indicator turns off.)
<Notes>:
to ten frames. That is, if an offset between the
master device and slave device exceeds ten
frames, the recorder interprets that as out of
sync, and tries to chase and lock to MTC sent
from the master device. (This operation is called
" re-chasing .") During the re-chase
operation, audio output is muted. If the slave
machine slips with MTC from the master device
by less than ten frames, the slave machine
continues running while recognizing the
slippage.
116
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
With the slave mode to "ON", the recorder
synchronizes only to incoming MTC. After it
locks to MTC, it continues to chase MTC by
varying the speed within the inaudible deviation
range. If it unlocks to the MTC, it automatically
rechase MTC.
With tha slave mode to "ON", once the recorder
locks to incoming MTC, it runs with the internal
clock reference. If it unlocks to MTC, it
automatically rechase MTC.
With tha slave mode to "ON", once the recorder
locks to incoming MTC, it stops chasing and
runs with the internal clock reference. It does
not rechase MTC even if it unlocks to MTC.
You need to input MTC from an
When you set the Slave type, the Vari
The recorder re-chase window is fixed
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
OL
24
BIT
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
Advertisement
Chapters
Table of Contents
