Fostex D2424LVmk2 Reference Manual page 16

Model D2424LVmkII Reference Manual (Names and Functions)
22. Locate key
[LOCATE]
Use this key to start to start the LOCATE feature.
Pressing this key after a memory key (CLIPBOARD
IN/OUT, AUTO RTN START/END, AUTO PUNCH IN/
OUT) locates the memory data programmed in each
respective key (time mode or bar, beat, clock
setting).
The data can be programmed by individually setting
it with one of the 99 (01-99) LOCATE numbers of
the [LOCATE] key.
Note that the data of memory number 00 is available
in addition to LOCATE numbers 01-99.
The last LOCATE time setting (bar, beat, clock
setting) constantly replaces the data stored in the
[LOCATE] key as data in memory number 00.
Therefore, it is possible to press this key alone to
repeatedly LOCATE the same point.
These data can be individually stored in programs
P1-P99. The data for each program is SAVED or
LOADED for each program when the song data is
designated for SAVE/LOAD in the SETUP mode.
This data is maintained even when the power is
turned OFF.
* Refer to page " 58 " for more information about the
Locate function.
23. Rewind button
[REWIND]
Pressing this button while the recorder section is
stopped will rewind data at 30 times speed.
Pressing this button in Play mode will cue data (you
can hear sound while rewinding) at five times speed.
Pressing this button while holding down the [STOP]
button will perform the "LOCATE ABS 0" operation,
and immediately locate the beginning of the
Program (ABS TIME: 00M: 00S: 00F). (Refer to the
"[STOP] button" section for more information about
LOCATE ABS 0.)
24. Undo/Redo key
[UNDO/REDO/M. UNDO]
If you wish to restore the status prior to editing,
recording, or performing a punch in/out take, press
the [UNDO/REDO] key. Pressing the [UNDO/REDO] key
again will return you to where you were before you
pressed the [UNDO/REDO] key the first time.
If the current drive you are using has been formatted
with the multiple undo function switched ON, you
can execute multiple undo by pressing this key while
holding down the [SHIFT] key.
<Note>:
This key is enabled only when the recorder
is stopped.
* Refer to pages " 45 ", " 47 ", " 73 " and " 76 " for more
information about the single Undo/Redo
operation.
* Refer to page " 69 " for more information about
Multiple Undo function.
25. Play button
Pressing this button will cause the recorder to play
back. Pressing this button while holding down the
[RECORD] button will start recording.
Pressing this button while holding down the [STOP]
button will perform the Clipboard playback
operation. Refer to the section "[STOP] button" for
more information on the Clipboard playback.
Pressing the [PLAY] button during recording will stop
recording.
26. Setup key
[SETUP/TC GEN]
Press this key to puts the recorder in the SETUP
mode to execute various operations. This key works
when the recorder is stopped. To exit from the
SETUP mode, either press the [EXIT/NO] key or the
[STOP] button. If the optional Model 8346 TC/SYNC
card is installed and external time code is being
input, you can enter the generator setup mode by
pressing this key while pressing on the [SHIFT] key.
* Refer to page " 108 " for more information on SETUP
mode.
* Refer to " APPENDIX " for more information about
generator setup mode.
27. Stop button
Pressing this button will stop the transport section
of the recorder. Pressing the PLAY, REWIND, or F
FWD button while holding down this button will
cause the recorder to perform the following
operation:
[STOP] button + [PLAY] button
Clipboard playback (The STOP LED will flash and
the PLAY LED will light up.) *1
[STOP] button + [REWIND] button
[STOP] button + [F FWD] button
Pressing the [STOP] button will abort the editing
operations and display the current position of the
recorder, if you wish to:
* quit the data edit mode,
* cancel the recall or store operation,
* quit the pitch data display,
* cancel the edit operation, such as pasting, or
* cancel the SETUP menu settings.
Pressing the foot switch while holding down this
button allows you to turn the punch in/out rehearsal
mode ON/OFF.
*1 Clipboard playback:
The recorder plays back the copy data or move data
for the Clipboard. During audio playback of the copy
or move data, the FL will display the time length and
data type ("Copy Clip Play!" or "Move Clip Play!"), and
the copy or move source track indicator will flash,
enabling you to quickly determine the track and data
type.
16
[PLAY]
[STOP]
Locate ABS 0 *2
Locate REC END *3