Table of Contents
Advertisement
Model D2424LVmkII Reference Manual (Punch In/Out)
This section explains how to perform Manual Punch In/Out using a foot switch.
You do not need to specify the Punch In/Out points. Instead, you press the foot switch at the Punch
In/Out point. Manual Punch In/Out also offers rehearsal and actual takes. You can repeat rehearsal
until you are ready. As an example, replace a part of the recorded guitar solo on track 3.
Preparation
Check to see that the guitar is connected to the input
jack of the mixer, as required for [AUTO PUNCH IN/
OUT] mentioned earlier.
(1)
Connect the foot switch (unlatch type) to the
[PUNCH IN/OUT] jack on the rear panel.
(2)
Set the foot switch function to "Punch I/O" (punch
in/out function) by the SETUP mode "Setup of the
foot switch function" menu.
Rehearsing Manual Punch In/Out recording
In Rehearsal mode, the READY track enters input
monitoring mode between the Punch In and Out
points (the points at which you press the foot
switch), and the sound is not recorded. You can
practice the Punch In/Out operation repeatedly
before you proceed to actual recording.
(1)
Press the foot switch while holding down the
[STOP] button.
"Rehearsal On" will appear on the display or about
1 second, then rehearsal mode will appear and the
REHEARSAL LED (green) of the [AUTO PUNCH] key
flashes.
AUTO
PUNCH
(2)
Press the [RECORD TRACK] select key [3/11/19]
to set track 3 to READY.
(3)
Press the [PLAY] button to play back from a point
slightly before the Punch In point.
Manual Punch In/Out
• Initialize the recorder.
• Select a desired Program for Punch In/Out.
• Check a sampling frequency of the recorder and external device.
Foot switch (unlatch type)
REHEARSAL
TAKE
(4)
Play the guitar accompanying the playback of
tracks 1 to 8.
The recording level and monitor volume is adjusted
on the mixer in the same manner as done for [AUTO
PUNCH IN/OUT] described earlier.
(5)
Press the foot switch once at the desired Punch In
point, then press the foot switch again at the
desired Punch Out point.
The rehearsal mode will operate as shown in the
figure. Between the Punch In and Out points the
current performance of the guitar will be played as
the guitar monitor sound. The previous recording
is heard in any other case. The RECORD LED lights
up when Punching In and turn off when Punching
Out (the REHEARSAL LED remains flashing).
Playback start point
Track 8
Track 7
Track 6
Track 5
Track 4
Track 3
Track 2
Track 1
All tracks are in playback
monitoring mode.
Press the foot switch
at the Punch In point.
(6)
When you finish rehearsing, press the [STOP]
button.
If you are still unsatisfied, repeat steps 3-5.
Cancelling Rehearsal mode
(1)
While holding down the [STOP] button, press the
foot switch.
The display shows "Rehearsal Off" for 1 second, then
the flashing REHEARSAL LED turns off and cancels
the rehearsal mode.
<Hint>:
To rehearse repeatedly, set the AUTO
RTN START point slightly before the Punch In
point, and the AUTO RTN END point slightly
before the Punch Out point. This will help you
concentrate on your performance or check the
recording level easily (especially since Manual
Punch In/Out involves operating the foot switch
operation as well as the recorder). (See <Hint-2>
in the "Rehearsing Auto Punch In/Out recording"
for more information.)
46
Punch In point
Punch Out point
(Rehearsal In)
(Rehearsal Out)
This part is changed.
Only track 3 in input monitoring.
All tracks are in playback
The sound is not recorded
monitoring mode.
at this time. The RECORD
LED flashes.
Press the foot switch
at the Punch Out point.
Playback end point
Advertisement
Chapters
Table of Contents
