Interface Connectors; Safety Information; Laser Safety; Laser Notice - Mita DP-1400 Instruction Handbook Manual

Introduction

Interface connectors

Important note on the interface connectors
Be sure to turn off printer power before connecting or disconnecting an interface cable to the printer. For pro-
tection against static discharge which may be applied to the printer's internal electronics through the inter-
face connector(s), keep any interface connector which is not in use capped using the protective cap supplied.
Use shielded interface cable.

Safety information

Laser safety

This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services
(DHHS) Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968.
This means that the printer does not produce hazardous laser radiation. Since radiation emitted inside the
printer is completely confined within protective housings and external covers, the laser beam cannot escape
from the printer during any phase of user operation.

Laser notice

This printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter for Class I
(1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC
825-1
CAUTION
Laser radiation when open. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
PRINTER
MACHINE No.
MANUFACTURED
60Hz 120V
THIS LASER PRODUCT CONFIRMS TO THE APPLICABLE
REQUIREMENTS OF FEDERAL REGULATIONS 21 CFR
CHAPTER 1, SUBCHAPTER J.
MITA INDUSTRIAL CO.,LTD.
2 - 28 1 - CHOME TAMATSUKURI
CHUO-KU OSAKA JAPAN
MADE IN JAPAN
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part of the CC Rules.
Operation is subject to the following two conditions
() This device may not cause harmful interference,
and () this device must accept any interference
received, including interference that may cause
undesired operation.
This Class B digital apparatus complies
with Canadian ICES-.
Cet appareil numrique de la classe B est
conforme la norme NMB- du Canada.
CAUTION
REMOVE POWER CORD BEFORE
SERVICE AND FUSE REPLACEMENT.
ATTENTION
POUR PRÉVENIR LES CHOCS
,
ÉLECTRIQUES, COUPER L ALIMENTATION
AVANT DE REMPLACER LE FUSIBLE.
PRECAUCION
RETIRE EL CORDON ELECTRICO ANTES
DE REALIZAR SERVICIO O REEMPLAZAR
EL FUSIBLE.
DP-1400
(U.S.A./Canada)
vi
PRINTER
MACHINE No.
MANUFACTURED
5.8A 60Hz 120V 7.8A
THIS LASER PRODUCT CONFIRMS TO THE APPLICABLE
REQUIREMENTS OF FEDERAL REGULATIONS 21 CFR
CHAPTER 1, SUBCHAPTER J.
MITA INDUSTRIAL CO.,LTD.
2 - 28 1 - CHOME TAMATSUKURI
CHUO-KU OSAKA JAPAN
YM YM
MADE IN JAPAN
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part of the CC Rules.
Operation is subject to the following two conditions
() This device may not cause harmful interference,
and () this device must accept any interference
received, including interference that may cause
undesired operation.
This Class B digital apparatus complies
with Canadian ICES-.
Cet appareil numrique de la classe B est
conforme la norme NMB- du Canada.
CAUTION
REMOVE POWER CORD BEFORE
SERVICE AND FUSE REPLACEMENT.
ATTENTION
POUR PRÉVENIR LES CHOCS
,
ÉLECTRIQUES, COUPER L ALIMENTATION
AVANT DE REMPLACER LE FUSIBLE.
PRECAUCION
The labels shown are affixed to the DP-1800 and the DP-1400.
RETIRE EL CORDON ELECTRICO ANTES
DE REALIZAR SERVICIO O REEMPLAZAR
EL FUSIBLE.
DP-1800