System Selector; To Display Pictures Complying With The Srgb Standard - Panasonic PTDZ8700U - DLP PROJECTOR Operating Instructions Manual

SYSTEM SELECTOR

This enables the projector to automatically recognize
input signals. Furthermore, if unstable signals are
input, the system format can be selected manually.
Press ▲▼ to select [SYSTEM
1 )
SELECTOR].
2 ) Press <ENTER> button.
Press ▲▼ to switch [SYSTEM
3 )
SELECTOR].
4 ) Press <ENTER> button.
J
VIDEO/S-VIDEO terminal input
signal
Select from AUTO, NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, SECAM, and PAL60.
Attention
z
[AUTO] mode is selected by default.
z
When the projector is not working properly in [AUTO]
mode, change the setting according to each SYSTEM
SELECTOR type.
Note
z
[AUTO] automatically selects from NTSC, NTSC4.43,
PAL, PAL-M, PAL-N, SECAM, and PAL60.
J
RGB1/RGB2 terminal input signal
z
480i, 576i, 576p signals
Select from RGB and YC
z
VGA60, 480p signals
Select from VGA60, 480p, and 480pRGB.
z
Other signals
Select from RGB and YP
Note
z
Refer to "List of compatible signals" (
available signals.
J
DVI-D terminal input signal
z
480p, 576p signals
Select from RGB and YC
z
Other signals
Select from RGB and YP
Note
z
Refer to "List of compatible signals" (
available signals.
z
Malfunction may occur or other problems could be
encountered with some equipment.
C .
B R
P .
B R
Æ
page 122) for
C .
B R
P .
B R
Æ
page 122) for
J
HDMI terminal input signal
z
480p, 576p signals
Select from Auto, RGB, and YC
z
Other signals
Select from Auto, RGB, and YP
Note
z
Refer to "List of compatible signals" (
available signals.
z
Malfunction may occur or other problems could be
encountered with some equipment.
J
SDI terminal input signal
(PT-DZ8700U/PT-DS8500U only)
z
Select from AUTO, 1 080/60i, 1 035/60i,
720/60p, 1 080/24p, 1 080/50i, 1 080/30p,
1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i.
z
Refer to "List of compatible signals"
Æ
( page 122 ) for available signals.
To display pictures complying
with the sRGB standard
sRGB is the international color reproduction standard
(IEC61966-2-1) established by IEC (International
Electrotechnical Commission).
To reproduce colors more faithfully in compliance
with the sRGB standard, perform the following setting
procedure.
1 ) Set [COLOR MATCHING] adjustment to
[OFF].
z
Refer to "COLOR MATCHING"
2 ) Display the [PICTURE] screen.
z
Refer to "PICTURE menu" (
Press ▲▼ to select [PICTURE MODE].
3 )
Press ◄► to select [NATURAL].
4 )
Press ▲▼ to select [COLOR].
5 )
6 ) Press <DEFAULT> button on the
remote control to restore the factory
default.
7 ) Follow the same procedure (steps
5-6) to restore the factory default for
[TINT], [COLOR TEMPERATURE] and
[GAMMA].
Note
z
sRGB is only enable when RGB signals are being input.
PICTURE menu
C .
B R
P
B R
Æ
page 122) for
Æ
( page 68).
Æ
page 52).
ENGLISH -
57