Adjust Tonal Quality For Each Speaker Using Graphic Equalizer (Manual - Denon AVR-590 Owner's Manual

Setting items
Dynamic EQ ON : Use Dynamic EQ function.
OFF : Do not use Dynamic EQ function.
Audyssey Dynamic EQ solves
the problem of deteriorating
• W hen set to "ON", "
sound quality as volume is
• W hen "MultEQ" is set to "OFF" , "Dynamic EQ" is automatically set
decreased by taking into
to "OFF"
account human perception
• T his can also be set by pressing
and room acoustics.
Dynamic EQ : ON/Volume : OFF
This can be set when the
"MultEQ" (vpage 41)
is set to anything other
than "OFF" .
NOTE
"Tone Control" is set to "OFF" when "Dynamic EQ" is set to "ON" .
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Setting is enabled when "Dynamic EQ" is "ON" .
Dynamic Volume ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
of the "Setting" (vpage 42)
Audyssey Dynamic Volume
OFF : Do not use Dynamic Volume.
solves the problem of
large variations in volume
• When set to "ON" , "
level between television
• When "MultEQ" is set to "OFF", "Dynamic Volume" is automatically
programs, commercials, and
set to "OFF".
between the soft and loud
• This can also be set by pressing
passages of movies.
Dynamic EQ / Volume : ON
This can be set when
"Dynamic EQ" (vpage
42) is set to "ON" .
Remote control
operation buttons
Setting contents
" is displayed.
.
Dynamic EQ / Volume : OFF
"Red" "Off"
"Green" "OFF"
" is displayed.
.
Dynamic EQ : ON / Volume : OFF
"Green" "Red"
"Green" "Red"
Displaying the menu
: Moves the cursor (Up/Down/Left/Right)
:
Cancel the menu
Setting items
Setting Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Set Dynamic Volume effect.
Evening : Middle setting prevents loud and soft sounds from being much
This can be set when
louder and softer respectively than average sounds.
"Dynamic EQ" (vpage
Midnight : High setting affects volume the most, causing all sounds to be
42) is set to "ON" .
of equal loudness.
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)
Setting items
Adjust CH 1. Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
Adjust the tonal quality of
the individual speakers. L/R CH : Adjust tonal quality for each L/R speaker pair.
Each CH : Adjust tonal quality for each speaker separately.
2. Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
b When "L/R CH" or "Each CH" is selected, select the speaker to be
adjusted.
3. Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Base Curve Copy Yes : Copy.
No : Do not copy.
Copy the MultEQ "Audyssey
Flat" correction curve.
"Base Curve Copy" is displayed after the Audyssey Auto Setup
procedure has been performed.
Default Yes : Reset to the defaults.
Reset the "Manual EQ" No : Do not reset to the defaults.
settings to their defaults.
: Decision the setting
ENGLISH
Adjusting the Sound Field Effect (Parameter)
Setting contents
Default settings are underlined.
Setting contents
: Return to previous menu