Denon AVR-590 Owner's Manual page 24

ENGLISH
Step 2 : Audyssey Auto Setup
Preparations
around items indicate the settings made upon purchase.
If adjustment to the environment is necessary, set the following
items before proceeding.
Changing the PRE OUT connectors assignment
(Pre Assign)
The signals output from the AVR-590's SURR. BACK / FRONT HEIGHT
PRE OUT connectors can be switched to signals of the surround mode
being used.
1
Press ui to select "Pre Assign".
2
o p
Press to select
Pre Assign Mode.
3-1.Audyssey Auto Setup 3-1.Audyssey Auto Setup
Please place microphone Please place microphone
at ear height at at ear height at
main listening position. main listening position.
[ENT]:Select [RTN]:Back [ENT]:Select [RTN]:Back
Normal
: The sound of the surround back channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
Front Height
: T he sound of the front height channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
n To cancel Audyssey Auto Setup
Use ui to select "Cancel" , then use

Step 3 : Performing the Audyssey Auto Setup Procedure
• The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
MultEQ corrects acoustical distortions within the listening area.
• Once started, MultEQ will play a series of test tones through each
speaker.
• Before starting, connect and position all of your speakers.
1
Press ui
"Start", then press
.
Detection of the speaker
configuration starts.
2
Once all the speakers
have been detected
MultEQ MultEQ
and the screen on
the right appears,
check the results
Pre Assign: Pre Assign:
Normal Normal
of detection of the
Start Start
Cancel Cancel connected speakers.
3
Once you have checked the results, use
"Next", then press
Measurements for the main listening position begin.
4
Once the screen on
the right appears,
move
microphone to the
o p to select "Yes" .
second position, use
ui to select "Next",
then press
Measurements for the second position begin.
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
to select
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Pre Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Step1:Speaker Detection
MultEQ
Front Sp. :Yes
Center Sp. :Yes
Subwoofer :Yes
Surround Sp. :Yes
S.Back Sp. :Yes
:2sp
Next
Retry
[ENT]:Next
ui to select
.
Step2:Measurement
MultEQ
Please place microphone
at ear height at
the setup
2nd listening position.
Next
Calculate
Cancel
[ENT]:Next
.
5
Perform Step 4 repeatedly for the 3rd, 4th, 5th, and
6th measurments.
Once measurements for the sixth position are completed, "All
the measurements were finished. " is displayed.
b Measure at a total of six positions, including the main listening
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
6
Once measurements
Step2:Measurement
are finished, use ui
All the measurements
were finished.
to select "Calculate",
then press .
Analysis begins.
[ENT]:Cancel
b Analysis takes several
minutes to complete.
The time required for
Step3:Calculating
this analysis depends on
Calculating
the number of speakers
Please wait...
connected. The greater
the number of speakers
connected, the longer
[----------]
analysis will take.
7
ui
Use to select the item you want to check, then
press .
Step4:Check
The measurement result
Please check the results
confirmation screen is
of the measured item.
displayed.
Speaker Config.Check
b
S ubwoofers or other Distance Check
Channel Level Check
speakers may be set to
Crossover Freq.Check
a value that does not
[ENT]:Select
correspond to the actual
distance.
MultEQ
Calculate
Retry
Cancel
⇩
MultEQ
MultEQ
Next