Convenient Functions; Hdmi Control Function; Setting The Power To Standby After A Certain Amount Of Time (Sleep Timer Function); Playing The Picture Of A Different Input Source Without Changing The Currently Playing Sound (Video Select Function) - Denon AVR-590 Owner's Manual

Convenient functions

HDMI Control Function

When you make an HDMI connection with a TV or player
compatible with AVR-590 and HDMI control functions, you can
perform the following operations by setting the HDMI control
function of each device.
n AVR-590 power off can be linked to the TV power
off step
W hen you set "Output audio from amp" in the TV audio
z
output setup operation, you can switch the amp power
on.
n
You can switch audio output devices with a TV
operation
n You can adjust AVR-590 volume in the TV volume
adjustment operation
n You can switch AVR-590 input source through
linkage to TV input switching
n When playing the player, the AVR-590 input
function switches to the function of that player
• To play the TV's sound on the AVR-590, make optical digital
connections (vpage 13 "Connecting the TV").
• To use this function, set "HDMI Control" (vpage 27) to "ON".
NOTE
• When you power off AVR-590, the HDMI control function does not
operate.
• Some functions may not operate depending on the connected
TV or player. Check the owner's manual of each device for details
beforehand.
• W hen "HDMI Control" is set to "ON", it is not possible to assign an
HDMI connector to "TV" at "HDMI" (vpage 27).
1
T urn the power on for all the equipment connected by
HDMI cable.
2
S et the HDMI control function for all equipment
connected by HDMI cable.
Set "HDMI Control" (vpage 27) to "ON" .
b Please refer to the owner's manual as regards setting of connected
devices.
b Carry out Steps 1 and 2 should any of the equipment be
unplugged.
3
S witch the television input to the HDMI connected to
the AVR-590.
4
S witch the AVR-590 input to the HDMI input source
and check if the picture from the player is ok.
5
W hen you turn the TV's power to standby, check that
the power of the AVR-590 and player also goes on
standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or player compatible with the HDMI control function?
• Is the AVR-590 properly set?
• Is "HDMI Control" (vpage 27) set to "ON"?
• Is "Power Off Control" (vpage 27) set to "ON"?
• Are the HDMI control function settings of all equipment correct?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step's 1 and 2.
• Menu "HDMI" (vpage 27) setting has changed.
• There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
Setting the power to standby
after a certain amount of time
(Sleep Timer Function)
This function allows you to automatically set the power to
standby after the set amount of time has passed.
Press and display the time you want to set.
The "SLEEP" indicator on the display lights.
• The time switches as shown below each time
Sleep:OFF Sleep:120min
Sleep:30min Sleep:60min
• The time display turns off after about 5 seconds, and the
setting is activated.
• Once the set time has passed, the power is automatically set
to standby.
n
To cancel the sleep timer
Press to set "OFF" .
• The "SLEEP" indicator on the display turns
off.
Playing the picture of a different
input source without changing
the currently playing sound
(Video Select Function)
Switch video input source while listening to audio signal.
Press until the desired picture
appears.
b To cancel, press to select "SOURCE" .
NOTE
• It is not possible to select HDMI input signals.
• When playing HDMI video input signals, the analog video signal of
another input source cannot be selected for the HDMI video output.
• Input sources for which "Delete" is selected at "Source Delete"
(vpage 28) cannot be selected.
• Input sources for which "None" is selected at "Assign" (vpage 31)
cannot be selected.
ENGLISH
is pressed.
Sleep:90min