Punch Through; Setting The Back Light's Lighting Time; Setting The Ambient Light Sensor; Setting The Brightness - Denon AVR-3806S Operating Instructions Manual

Advanced Operation

Punch through

Buttons used in the CD, DVD, and VCR modes can be assigned
to the buttons which are not normally used in the TV and
SAT/CBL modes.
For example, when the DVD mode is set to the punch through
mode in the TV mode, the DVD mode's PLAY (1), STOP (2),
MANUAL SEARCH (6, 7), AUTO SEARCH (8, 9)
and PAUSE (3) button's signals are sent in the TV mode. — (
1 1
SET UP SETUP
Press and hole the Press and hold the
three seconds. three seconds.
• The IR segment blinks twice. • The IR segment blinks twice.
2 2
9, 8, 4 9, 7, 8
Press the Press the button (9 button (9
punch through setting. setting.
• The IR segment blinks twice. • The IR segment blinks twice.
3
Select the MODE SELECTOR button (CD, DVD or
VCR) you want to punch through.
4
Press the button you want to punch through (
2 , 6 , , 8 , 9 or
7
5
Repeat step 4.
6
Press the MODE SELECTOR button(TV or
SAT/CBL) for which you want to set the punch
through.
7
SETUP
Press and hold the
three seconds.
• The IR segment blinks twice.

Setting the back light's lighting time

1 1
Press and hole the Press and hold the
three seconds. three seconds.
• The IR segment blinks twice. • The IR segment blinks twice.
2 2
Press the Press the
)
setting. Light setup.
• The IR segment blinks twice. • The IR segment blinks twice.
button for at least button for at least
3
Press the
adjust the lighting time (5 sec ~ 25 sec).
to select a to select
2 2 Lighting time
1 : 5 sec
2 : 10 sec (factory default)
3 : 15 sec
4 : 20 sec
5 : 25 sec
• The IR segment blinks twice as confirmation.
1 ,
3 ).

Setting the ambient light sensor

The included remote control unit (RC-1024) has the ambient light
sensor which allows the EL display brightness to automatically
adjust depending on how light or dark the amount of
incandescent light in the room is. Default state of the ambient
light sensor is "OFF" (disable).
1 1
Press and hold the Press and hole the
three seconds. three seconds.
• The IR segment blinks twice. • The IR segment blinks twice.
button for at least
2 2
Press the
Press the
setting.
• The IR segment blinks twice.
• The IR segment blinks twice.
3
Press the
• The IR segment blinks two or four times.
Two blinks indicates that ambient light feature was disabled,
and is now enabled. Four blinks indicates that ambient light
feature was enabled, and is now disabled.
SET UP SETUP
button for at least button for at least
9, 7, 3 9, 7, 8
button (9 button (9 to select a to select
NUMBER
button (1 to 5) you want to
SET UP SETUP
button for at least button for at least
9, 7, 8
button (9 to select a
9, 7, 9
button (9 .
ON
button.
54
• If you want to set the brightness of the display manually, set to
"OFF" (default).

Setting the brightness

• The brightness of the display can be adjusted in 5 levels.
• The default brightness setting is level3 (level 5 = brightest).
1
SETUP
Press and hold the
three seconds.
• The IR segment blinks twice.
2
For 1 brightness step increase:
CHANNEL +
Press the button.
-1
2
For 1 brightness step decrease:
CHANNEL –
Press the button.
-2
3
SETUP
Press and hold the
programing.
• The IR segment twice as confirmation.
Advanced Operation
button for at least
button to exit