Advertisement
(Š FUNCTION Keys
R/T (Reverb Time) Key
Press
the
"EDIT"
key before using this key.
Press
this key,
and the LED in the middle
will
light.
Reverberation
time can now be
changed.
Monitoring
the change on the "REV.
TIME" display
in the far left column,
above
the "DIRECT" sound level control,
the rever-
beration
time value can be changed with
either
the ten numeric keys,
or the "UP" and
"DOWN" keys.
Do not forget to press the
"ENTER" key last of all for input with the
numeric
keys.
D] (Delay 1) Key
Press
the
"EDIT" key before using this key.
Press
this key,
and the LED in the middle of
the key will
light.
Early reflection
delay
data can now be entered
or altered.
Monitoring
the change on the "E/R DELAY 1
(DD" display in the second to the far left
column,
above
the "EARLY REFLECTION"
level
control,
the DELAY ] value can be changed with
either the ten numeric keys, or the "UP" and
"DOWN "keys.
Шо not forget to press the
"ENTER" key last of all for input with the
numeric keys.
Pressing this key and the "D2"
key at the same
time will enable you to modi-
fy the DELAY ] and DELAY 2 data with the same
value simultaneously
(see number 15 of the
"Front Panel Controls" section).
D2 (Delay 2) Key
Press
the
"EDIT" key before using this key.
Press
this key,
and the LED in the middle of
the key will
light.
Subsequent reverberation
delay data can now be entered
or altered.
Monitoring the change on the "REV. DELAY 2
(D2)" display in the second to the far right
column,
above the "REVERBERATION"
level con-
trol,
the DELAY 2 value can be changed with
either the ten numeric keys, or the "UP" and
"DOWN" keys.
Do not forget to press the
ENTER" key last of all for input with the nu-
meric keys.
M (Memory) Key
I
Press the
EDIT" key before using this key.
Press
this key,
and the LED in the middle of
the key will
light.
The memory number can
now be changed.
Monitoring
the change of the
"MEMORY" display above,
the memory number can
be changed with
the ten numeric keys.
Press the "STR (store)" key to write in the
memory,
or the "RCL (recall)" key to read data
from the memory.
(9 Ten-Key Numeric Pad (incl.
10 digits
and decimal point)
These keys are used
to change
the values
of
each function
(E/R DELAY 1, REV DELAY 2,
MEMORY").
The user can enter data while mon-
itoring
the display of the specified
function.
@ CLEAR Key
Used
to clear
the value of a specified
func-
tion on display.
Used when data must be mod-
ified or to correct
incorrect
data.
UP and DOWN Keys
Used to increase or decrease
the value of a
specified
function
(except for memory numbers).
They are convenient
in setting
the level
to an
optimum while monitoring.
(& ENT (Enter) Key
Press
this key to enter data from the numeric
keys.
Data will not be entered
if this key
is not pressed
before
the function
is changed
with a function key.
00 MASTER ON Key
Press the "EDIT" key in the upper right hand
corner of the panel before using this key.
When lit,
the mixed signal
will be on the
output;
when pressed again,
the LED goes out,
and the mixed signal will be cut from the
outputs.
(db MASTER Level Indicator
This
is the set of three LEDs above
the
"MASTER" selector.
It is used to indicate if
the mixed signal
read from a memory
is larger
than,
smaller
than,
or equal
to the current
setting of the "MASTER"
level control under-
neath
it.
19 MASTER Level Control
Press the "EDIT" key in the upper right hand
corner
of the panel
before using this level
control.
Then adjust
it until
the LED in the
center of the indicator
above
is lit.
After
that,
it can be used.
It controls
the
output
level of the mixed signal,
which con-
tains
the "DIRECT"
sound,
"EARLY REFLECTION",
and "REVERBERATION"
outputs.
20
Advertisement
