General Requirements - Vulcan-Hart PRECIPAN VPP28 Installation Manual

3V-490072NI – 06/23
⚫ GUARANTEE.
To ensure the guarantee on this equipment you need to comply with the MANUFACTURERS INSTRUCTIONS in this document.
However, if you cannot undertake the required maintenance operations, our installation and service network is available to provide you with a
personalized contract.
⚫ WARNING
- This product complies with current standards. If any modifications are made the manufacturer cannot accept any responsibility whatsoever.
The manufacturer cannot be held responsible in the event of any inappropriate use of the equipment.
- When handling it, this appliance must remain on its base until final installation.
- This equipment is intended for use by suitably trained professionals
- Read all the documentation carefully before installation.
- Keep your documents for future reference.
- Translation of the original manual
⚫ A qualified engineer must carry out the installation, modification, or repair of the appliance in a workmanlike manner.
⚫ The unit should be installed in a normally and sufficiently ventilated environment to prevent the build-up of unacceptable levels of toxic
substances in the area it is being used.
⚫ This unit is not designed to function in an explosive atmosphere. Accordingly, it should be installed in an area as directed by ATEX.
⚫ This unit should be installed in accordance with EN 1717 and current local regulations for water connection.
⚫ If these units are installed against a wall or a partition, this must be of non-combustible materials or, if not, it must be covered with an
appropriate, good insulating and non-combustible material.
⚫ Unless specified otherwise, the parts protected by the manufacturer, or his authorized representative must not be handled by the installer.
⚫ Always comply with regulations and standards concerning connections to water, waste, and electricity.
⚫ ATTENTION – Isolate electrically before any form of intervention or maintenance.
⚫ This unit should be assembled in compliance with guidelines for their stability and consequent safety.
⚫ For mobile units always handle with care to avoid them tipping over.
⚫ Mobile units should never be moved with hot liquid in the well they should be drained down first.
⚫ For units on a masonry plinth (see section "Assembly of units on a plinth"), all necessary precautions should be undertaken by the installer to
avoid the appliance slipping or tipping.
⚫ The manufacturer certifies that the packaging meets the provision 94/62/CE (relating to packaging and packaging waste of 20.12.94) and
requests that the final installer (or user) observes the rules relating to the removal of the packaging (recycling or reuse).
⚫ The manufacturer disclaims any liability in the event that the above instructions are not followed.
⚫ The appliance should only be handled with suitable lifting equipment. Should the appliance need to be transported, this must be on its original
pallet, and it must not be stacked on other appliances under any circumstances. If the appliance is to be moved without its pallet, it should be
carried and not pulled. Fig. 1.1A, 1.1A'.'
ASSEMBLY ON INDIVIDUAL LEGS
The unit should be levelled using the adjustable feet (0.8 inch spanner). Fig. 2.1A → 2.1C
ASSEMBLY CANTILEVERED OFF A WALL
The unit should be levelled using the adjustable feet (0.8 inch spanner). Fig. 2.3A → 2.3F
The cantilever support must be able to take 400 daN (2 supports for an 1100 or 1400 unit). For units cantilevered off a concrete wall the
following are recommended:
* Reinforced concrete of a minimum quality of 23 MPA (DTU).
* Use rawl plugs such as HSA-R M 8 x 75 or equivalent.
* For the rawl plugs above the hole to be drilled should be 0.3 inch and to a depth of 2.6 inch minimum (WARNING! The minimum distance
between the plug holes to the edges and corners of the wall must be at least 3.8 inch (95 mm)).
F49570 (06-23)
Page 2

GENERAL REQUIREMENTS

LOCATING
VULCAN
A division of ITW Food Equipment Group LLC
P.O. Box 696
Louisville, KY 40201
EN