1. Manuals
  2. Brands
  3. Rimage Manuals
  4. Printer
  5. Amigo II
  6. User manual

Rimage Amigo II User Manual

Rimage amigo ii: user guide
Hide thumbs Also See for Amigo II:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual
TM
Rimage Amigo II
User Guide

Advertisement

Table of Contents
loading

Related Manuals for Rimage Amigo II

Summary of Contents for Rimage Amigo II

  • Page 1 Rimage Amigo II User Guide...
  • Page 2 Rimage Corporation is not responsible for the content of any such third-party site. ©2007, Rimage Corporation Rimage™ is a trademark of the Rimage Corporation. Amigo II™ is a trademark of the Rimage Corporation. Dell is registered trademark of Dell Computer Corporation. ® FireWire is a registered trademark of Apple Computer, Inc.

  • Page 3: Support Information

    FAX: 952-946-6956 Rimage Support Website: http://www.rimage.com/support.html Product Family and then select your product. If you cannot find a solution on our website, email Rimage Services at support@rimage.com. When you contact Rimage Services, please provide: • Unit serial number and software version.

  • Page 4: Table Of Contents

    Media requirements ... 1 Ribbon requirements ... 1 Label design requirements ... 1 Networking ability ... 1 Identify the parts of the Amigo II ...2 Front view ... 2 Rear view... 3 Operate the Amigo II...4 Powering on the Amigo II... 4 Pausing the system ...

  • Page 5: Introduction

    Introduction Introduction This manual provides the information needed to operate the Amigo II and identify the parts. To set up and install your Amigo II, refer to the Amigo II Setup and Installation Guide. The Amigo II is available with either the Everest Printer or the PrismPlus Printer.

  • Page 6: Identify The Parts Of The Amigo Ii

    Active LED Operator Button Power LED Fault LED Operator Button Each time you press the operator button, the carousel rotates to the next bin. Tip: The carousel will rotate to a bin only after the Amigo II has completed initializing. 110654_G...

  • Page 7: Rear View

    It flashes with the carousel present LED to indicate a paused state. Power The green Power LED illuminates when the Amigo II is powered on. If an error is detected, the yellow Fault LED, located on the operator button, Fault illuminates during the button diagnostics.

  • Page 8: Operate The Amigo Ii

    Setting up your printing preferences Printing Preferences allows you to set up and run your Amigo II to produce the best possible label on your discs. Please refer to your Everest Printer User Guide or PrismPlus! Printer User Guide for specific printing preferences instructions.

  • Page 9: Maintain The Amigo Ii

    T 25 Torx screwdriver 5/32” Allen wrench To power on the Amigo II, press the Amigo II power switch. Wait until the unit completes the initialization. Tip: The Everest II Printer takes 1 to 2 minutes to complete the initialization.
  • Page 10 Side to Side Alignment Print If the disc is not centered side to side on the print pad, align the printer side to side. Loosen the side to side screws. Slide the printer, not the print drawer, until the side edges of the disc and printer pad are aligned.

  • Page 11: Prismplus Printer

    Required tools: T 25 Torx screwdriver 5/32” Allen wrench To power on the Amigo II, press the PrismPlus power switch and the Amigo II power switch. Wait for the unit to complete the initialization. Prepare the unit for alignment. Manually move the lift arm to the top of the Amigo II.
  • Page 12 Rimage Amigo I If the disc is not centered side-to-side on the print pad, align the printer side to side. Loosen the side to side screws. Slide the printer, not the drawer, until the side edges of the disc and printer pad are aligned.

  • Page 13: Learn More

    95 lbs (43.2 kg) with Everest printer • 71 lbs (32.3 kg) with PrismPlus printer Drive one is used to house the operating system and the Rimage System Folder. Drive two is used for caching. Format drive as Basic Disk, NTFS.

  • Page 14: Technical Support And Product Updates

    Technical support and product updates Support for the Amigo II is available through your authorized reseller. Important! Register your Amigo II online or complete and return the registration card so Rimage can notify you of upgrades as they become available.

  • Page 15: Compliance Testing

    Compliance testing Product name: Amigo II Model: RAS9 Notice for USA Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Table of Contents