Field Wiring - Daikin R32 Sky-Air RZAG-M Service Manual

ESIE17-08 | Part 5. Appendix
Figure 5-5: Wiring diagram - outdoor unit RZAG100-140MV1, RZASG125-140MV1, AZAS125-140MV1
RZAG100-140MV1, RZASG125-140MV1, AZAS125-140MV1
OUTDOOR
Layout
Front
Back
Position of compressor terminal
Notes
1. Refer to the wiring diagram sticker (on the back of the front plate) for how to use the BSI~BS3 and DS1 switches.
2. When operating, do not short-circuit protection device(s) S1PH, S1PL and Q1E.
3. Refer to the combination table and the option manual for how to connect the wiring to X6A, X28A and X77A.
4. Colours: BLK: Black, RED: Red, BLU: Blue, WHT: White, GRN: Green.
Legend
A1P Printed circuit board (main)
A2P Printed circuit board (noise filter)
BS1~3 (A1P) Push-button switch
DS1 (A1P) Dipswitch
E1~3 (A1-2P) Connector
E1H * Bottom plate heater
F3U (A1P) Fuse T 6,3 A 250 V
F5U (A2P) Fuse T 56 A 250 V
F6U (A1P) Fuse T 5 A 250 V
F7U (A2P) Fuse T 6,3 A 250 V
F8U (A2P) Fuse T 6,3 A 250 V
F9~10U * Fuse F 1 A 250 V
HAP (A1P) Light-emitting diode (service monitor is green)
K1R (A1P) Magnetic relay (Y1S)
K2R (A1P) Magnetic relay (Y2S)
K4R (A1P) Magnetic relay (E1H)
K13R~K15R, Magnetic relay
K10R (A1P)
K11M (A1P) Magnetic contactor
L* (A1-2P) Connector
M1C Compressor motor
M1~2F Fan motor
PFC (A1P) Power factor correction
PS (A1P) Switching power supply
Q1DI Earth leakage circuit breaker (30mA)
Q1E Overload protection
R1T Thermistor (air)
R2T Thermistor (discharge)
R3T Thermistor (suction)
R4T Thermistor (heat exchanger)
R5T Thermistor (heat exchanger middle)
R6T Thermistor (liquid)

5.3.3. Field wiring

Not applicable.
15/11/18 | Version 1.1
R32 Sky-Air RZAG-M
Only for
RZASG125/140*
and AZAS125/140*
SEE
NOTE 3
Lower fan
Only for RZAG100/125/140*
Only for
RZAG100/125/140*
INDOOR
SEE NOTE 3
SEE NOTE 3
R7T Thermistor (fin)
R8 (A1P) Resistor
S1PH High pressure switch
S1PL Low pressure switch
SEG1~3 (A1P) 7-segment display
TC1 (A1P) Signal transceiver circuit
U, V, W (A1P) Connector
V1 (A1P) Varistor
V1D (A1P) Diode
V*R (A1P) Diode module
X*A (A1~2P) Connector
X1M Terminal strip
Y1E, Y3E Electronic expansion valve
Y1~2S Solenoid valve (4-way valve)
Z*C Noise filter (Ferrite core)
Z*F (A1~2P) Noise filter
* Optional
# Field supply
Symbols
Connection
X1M Main terminal
Earth wiring
Field supply
Several wiring possibilities
Protective earth
Field wire
Wiring depending on model
Option
Switch box
PCB
5.3. Wiring diagram
Lower EEV
Upper EEV
4D109863
Page 123