Wiring Diagram; Indoor Unit - Daikin R32 Sky-Air RZAG-M Service Manual

ESIE17-08 | Part 5. Appendix

5.3. Wiring diagram

5.3.1. Indoor unit

Outdoor
H05VV-U4G2,5
(see note 3)
PE
X2M 1 2 3
X1A
F1U
1
2
F2U
YC
Y2
Adapter for wiring (see note 5)
Notes
1. In case using central remote controller, connect it to the unit in accordance with the attached installation manual.
2. In case of main/sub changeover. See the installation manual attached to remote controller.
3. Shows only in case of protected pipes. Use H07RN in case of no protection.
4. When connecting the input wires from outside, forced off or on/off control operation can be selected by the remote controller. See installation manual for more details.
5. Connect power of adapter for wiring to terminal block (X2M) of indoor unit directly.
6. X35A, X39A, X70A are connected when the optional accessories are being used. In case an auto cleaning panel is used, see the wiring diagram.
Legend
A1P Main PCB
A2P Adapter PCB
A3P, A4P * Sensor kit PCB
A5P, A6P Receiver/display PCB
A7P * Adapter for wiring
BS01 (A6P) Push button (ON/Off)
C105 (A1P) Capacitor
DS1 (A1P) DIP switch
F1U (A7P) Fuse B, 5 A 250 V
F2U (A7P) Fuse B, 5 A 250 V
HAP (A1P) Running LED (service monitor-green)
H1P (A6P) LED (On-red)
H2P (A6P) LED (timer-green)
H3P (A6P) LED (filtersign-red)
H4P (A6P) LED (defrost-orange)
H5P (A6P) LED (element cleaning-red)
H6P (A6P) LED (ventilation cleaning-green)
KCR (A7P) Magnetic relay
KFR (A7P) Magnetic relay
KHuR (A7P) Magnetic relay (Hu)
K2R Magnetic relay
M1F Fan motor (indoor)
M1P Motor (drain pump)
M*S Motor (swing flap)
PS (A1P) Power supply
R1T Thermistor (air)
R2T Thermistor (liquid piping)
R3T Thermistor (coil)
RC (A1P) Signal receiver circuit
SS1 (A5P) Selector switch (emergency)
SS2 (A5P) Selector switch (wireless address set)
S1L Float switch
TC (A1P) Signal transmission circuit
15/11/18 | Version 1.1
Figure 5-1: Wiring diagram - indoor unit
S1L
t° t° t°
R2T R1T Z2C R3T
N=1
A1P
X15A X18A X16A NE X17A
1 2 1 2 1 2 3 4 1 2 3
X27A
K2R
BLK
1
Z1F
2
WHT
3
V1R
4
RED
(see note 6)
5 1 2 3 4 5 6 1 2 1 2
X33A TC RC X35A X20A
Z1C
A7P
X2A
N=1
Terminal for operation display
1 2 3 4 5 6
X1 Compressor
KhUr
KCR X1Y
operation
X2
1 2 3 4 5
X3
Fan operation
KFR
X4
M1F
R32 Sky-Air RZAG-M
Sensor kit
A2P
1 2 3 4 A3P
A4P
CN1
1 2 3 4 5 6 1 2 3 4
X83A
1 2 3
X39A
X1M T2 T1 F2 F1
1
2
C105
(see
PS
note 6)
X81A X30A
1 2 3 4 5 6 7 8 9 10 1 2 3
3 4 5 6 7 8
EMG
ON DS1
X70A
OFF
HAP
1
1 2
(see note 6)
2 NORM.
1 2 3 4 5 6 7 8 9 10 111213141516171819 20
X36A
M M M M
MS
M4S M3S M2S M1S
V1R (A1P) Diode module
X1A (A7P) Connector (power supply for option PCB)
X2A (A7P) PCB connector (sensor kit)
X24A (A1P) PCB connector (wireless remote controller)
X33A (A1P) PCB connector (adapter for wiring)
X35A (A1P) PCB connector (auto clean panel)
X39A (A1P) PCB connector (auto clean panel)
X70A (A1P) PCB connector (auto clean panel)
X*A PCB connector
X*M Terminal strip
X*Y Connector
Z*C Noise filter (ferrite core)
Z*F Noise filter
* Optional
# Field supply
Symbols
X1M Main terminal
Earth wiring
Wire number 15
Field wire
Field cable
Connection ** continues on page 12 column 2
Several wiring possibilities
Option
Not mounted in switch box
Wiring depending on model
PCB
Colours
BLK: Black
WHT: White
RED: Red
Input from outside (see note 4)
Central remote controller (see note 1)
R1T
P
(see note 2)
N
t°
User interface
P N
A5P A6P
X24A X2A
BS1
X1A
X1A
1 1
4 5 6 7 8
1 1
2 2
2 2
3 3
3 3 H1P
4 4
4 4
5 5 H2P
5 5
1 2 3
H3P
SS1
6 6
X25A
1 H4P
7 7
OFF ON
8 8 H5P
SS2
1 9 9
H6P
MS OFF ON
M1P
Receiver / display unit
4D099158-1
5.3. Wiring diagram
Page 119