CYBEX SOLUTION B3 I-FIX User Manual page 8

PRODUCT PARTS
EN
(a) User Guide Storage
Compartment
(b) Backrest
(c) Adjustable Headrest
(d) Headrest Height Adjuster
(e) Booster
(f) Lap Belt Guide
(g) Shoulder Belt Guide
INITIAL ASSEMBLY
Connect the backrest (b) to the booster (e) by hooking the guide lug on the
axis of the booster. The backrest (b) is then folded forward.
THE CORRECT POSITION IN THE VEHICLE
With retracted ISOFIX locking arms (i) the car seat can be used on vehicle
seats which are equipped with an automatic three point belt. For using ISOFIX
please refer to the list of compatible vehicles on www.cybex-online.com.
Above a child's stature of 135cm, the compatibility between the Solution B3
i-Fix and your vehicle might be reduced. Please review the list of compatible
vehicles to check whether the car seat can be used in all headrest positions
without restrictions.
In exceptional cases, the car seat may also be used on the front passenger
seat. Always comply with the recommendations of the vehicle manufacturer.
INSTALLING THE CAR SEAT IN THE VEHICLE
1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Use the ISOFIX adjustment handle (j) under the booster (e) and pull the two
ISOFIX locking arms (i) to their furthest extent.
3. Now twist the ISOFIX locking arms (i) 180° so that they are facing the
direction of the ISOFIX anchorage points (m).
4. Place the car seat on the appropriate seat in the vehicle.
5. Push the two locking arms (i) into the ISOFIX anchorage points (m) until
these lock into place with an audible "CLICK".
6
(h) Linear Side-impact Protection
(L.S.P.)
(i) ISOFIX Locking Arms
(j) ISOFIX Adjustment Handle
(k) ISOFIX Release Button
(l) ISOFIX Safety Indicator
(m) ISOFIX Anchorage Points
6. Use the ISOFIX adjustment handle (j) and push the car seat against the
vehicle seat.
7. Ensure that the entire surface of the backrest (b) of the car seat is placed
against the backrest of the vehicle seat.
��
If the headrest of the vehicle is in the way, pull it upwards to its furthest
extent or remove it completely (except in rear-facing vehicle seats).
8. Ensure the seat is secure by trying to pull it out of the ISOFIX anchorage
points (m). The green safety indicators (l) must be clearly visible on both
sides of the car seat.
9. In case the seat is used without ISOFIX, it can be stored away on the bottom
of the car seat.
��
By using ISOFIX, a connection to the vehicle is created which increases
your child's safety. Your child still needs to be secured with the three-point
belt of the vehicle.
If the Linear Side-impact Protection (L.S.P.) is in conflict with the vehicle
��
door or if it affects the space on the passenger seat, it is possible to detach
it. Proceed the following steps: Pull off the cover of the car seat on the sides
of the backrest. Press the hooks that fix the Linear Side Impact Protection
(L.S.P.) to the car seat and pull the Linear Side-impact Protection (L.S.P.)
out of the opening. In order to put the Linear Side-impact Protection (L.S.P.)
back on the car seat, clip it onto the marked area on the side of the car seat
and push until it clicks into the slot.
REMOVING THE CAR SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.
1. Unlock the ISOFIX locking arms (i) on both sides by pushing the release
buttons (k) and pulling them back simultaneously.
2. Pull the car seat away from the ISOFIX anchorage points (m).
3. Remove the car seat and store the ISOFIX in reverse order to installation.