Table of Contents
Advertisement
8)
Press asqw to select [RESOLUTION].
f Select [1024x768p], [1280x720p], [1280x800p], [1400x1050p], [1600x900p], [1600x1200p], [1920x1080p],
[1920x1200p], or [3840x2400p].
9)
Press the <执行> button.
f The [VERTICAL SCAN FREQUENCY] screen is displayed.
10) Press qw to select [VERTICAL SCAN FREQUENCY].
f Select [60Hz], [50Hz], or [30Hz] when [3840x2400p] is selected for [RESOLUTION].
f Select [120Hz], [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for
[RESOLUTION].
f Select [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
g [3840x2400p], [1920x1080p]
11) Press the <执行> button.
f The confirmation screen is displayed.
12) Press qw to select [OK], and press the <执行> button.
Note
f The settings in [RESOLUTION] and [VERTICAL SCAN FREQUENCY] are displayed in [EDID STATUS].
f The resolution and vertical scanning frequency settings may also be required on your computer or video device.
f The computer, video device, or projector in use may require the power to be turned off and on again after configuring settings.
f A signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video
device.
When the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10C) is installed
Setting [SDI MODE] in [SLOT 输入] (SDI input)
Switch input/output of the <SDI 2 输入/1 输出> terminal and the <SDI 4 输入/3 输出> terminal.
1)
Press as to select [SLOT 输入].
2)
Press the <执行> button.
f The [SLOT 输入] screen is displayed.
3)
Press as to select [SDI MODE].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
[INPUT]
[OUTPUT]
Note
f The <SDI 2 输入/1 输出> terminal and the <SDI 4 输入/3 输出> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f The <SDI 2 输入/1 输出> terminal and the <SDI 4 输入/3 输出> terminal support the output of the HD-SDI signal, 3G-SDI signal, 6G-SDI
signal, and 12G-SDI signal.
f When the projector is in standby mode, a signal is not output from the <SDI 2 输入/1 输出> terminal and the <SDI 4 输入/3 输出> terminal.
Setting [SDI LINK] in [SLOT 输入] (SDI input)
1)
Press as to select [SLOT 输入].
2)
Press the <执行> button.
f The [SLOT 输入] screen is displayed.
3)
Press as to select [SDI LINK], and press the <执行> button.
f The [SDI LINK] screen is displayed.
4)
Press as to select the setting.
Chapter 4 Settings — [DISPLAY OPTION] menu
Select this item when using the <SDI 2 输入/1 输出> terminal and the <SDI 4 输入/3 输出> terminal
as SDI2 input and SDI4 input.
Select this item when the signal input to the <SDI 1 输入> terminal is output from the <SDI 2 输入/1
输出> terminal, and the signal input to the <SDI 3 输入> terminal is output from the <SDI 4 输入/3 输
出> terminal.
ENGLISH - 151
Advertisement
Table of Contents
