Tools, Servicing Aids; Tools, Aids - Stihl MS 500i Service Manual

29 Tools, Servicing Aids

29.1

Tools, aids

Part number Designation
0000 890 2201 Assembly tool
0000 890 2300 Screwdriver
0000 890 2800 Assembly hook
0000 893 3706 Jaws (with profile 3.1 + 4)
0000 893 3711 Jaws (with profile 6)
0000 893 5904 Locking strip
0811 611 8200 Circlip pliers DIN5254-A10 or equivalent tool
0812 542 2041 Insert T20x125 or similar tool
0812 542 2104 Insert T27x125 or similar tool
1108 893 4700 Assembly drift
1113 893 4600 Press sleeve
1117 890 0900 Assembly tube
1141 893 4600 Assembly sleeve
1142 890 3400 Combination wrench
1142 893 2600 Clamping strap
1143 893 2400 Press sleeve
4119 893 2400 Press sleeve
4180 893 4400 Extension piece
5910 840 0210 Analyzer MDG 1
5910 840 0405 Diagnosis cable, fuel injection
5910 890 0302 Torque wrench with optical/acoustic signal or
equivalent tool
5910 890 0312 Torque wrench with optical/acoustic signal or
equivalent tool
5910 890 2212 Assembly tool
5910 890 2222 Service tool AS
5910 890 2301 Screwdriver T20 or equivalent tool
5910 890 2308 Screwdriver T10 or equivalent tool
5910 890 2405 Screwdriver Q-4x150
5910 890 2415 Screwdriver T27x200 or equivalent tool
5910 890 2420 Screwdriver Q-SW 8x200 or equivalent tool
5910 890 2800 Assembly hook
5910 890 3000 Stud puller, M8-7.5
5910 890 3101 Assembly stand
5910 890 3200 Cover
5910 890 4000 Wiring tool
5910 890 4400 Puller
5910 890 4504 Puller
5910 890 4505 Puller
5910 893 0501 Stud driver M8
5910 893 2804 Insert 13 mm long or equivalent tool
64
Use
Installing rope guide bushing
Disassembling, assembling clutch
Removing oil seals
Removing oil seals
Blocking the piston
Removing, installing circlip
Removing and installing hexagon socket head
screws with electric or pneumatic screwdrivers,
tightening with torque wrench
Removing and installing hexagon socket head
screws with electric or pneumatic screwdrivers,
tightening with torque wrench
Removing, installing piston pins
Pressing out ball bearing
Installing chain brake spring
Installing the oil seal
Installing the cylinder
Installing the oil seal
Removing, installing ball bearing
Removing, installing crankcase half grommets
Calibrating the chain saw; testing the chain saw,
replacing control unit
Calibrating the chain saw; testing the chain saw,
replacing control unit
Screw connections (1 to 18 Nm / 9 to 159 lbf. in.)
Screw connections (6 to 80 Nm / 5 to 59 lbf. in.)
Fitting snap ring on piston
Disassembling crankcase
Removing, installing hexagon head socket screws
Removing, installing hexagon head socket screws
Removing, installing hexagon head socket screws
Removing, installing hexagon head socket screws
Screwing in collar screws
Covering chain saw
Pressing wires into the guides
Removing oil seals
Removing the flywheel
Remove crankshaft
Unscrewing collar screws
Removing, installing decompression valve
MS 500i