3M PELTOR WS LiteCom Pro III MT73H7 4D10EU Series Manual page 6

GB
to a Bluetooth device, [+] and [–] buttons will control the
®
Bluetooth audio playback. Otherwise, the [+] and [–] buttons
®
will control surround volume level. The respective volume
levels can also be adjusted in the Menu.
4.5 Menu
To enter the menu, make a short press on the On/Off/Mode
button. Use the on/off/mode button to navigate through the
menu and the [+] and [–] buttons to adjust the respective
setting.
These are the options available in the menu:
• Channel
Lists all the programmed channels in the headset, up to 70.
• Radio volume
Adjusts the volume level of the incoming radio sound.
(OFF, 1 – 5)
• Surround volume
The surround, or level-dependent, feature uses external
microphones to sense the surrounding environmental noise
level. At noise levels above 82 dB, the level-dependent
technology will limit environmental sound reproduction within
the headset to a maximum of 82 dB. (OFF, 1 – 5)
• Bluetooth radio volume
®
Adjusts the volume level of a Bluetooth
munication radio, 1 – 5.
• Bluetooth pairing
®
Press plus button to set the headset in pairing mode. Press
down button to exit pairing mode.
• Battery status
Battery status is measured and the result is played to the
user. Press plus button to repeat the information.
• Language
Adjusts the ghost voice language between all installed
languages.
• Sub channel/ Color code (if activated)
Sets the subchannel of an analog channel according to lists
(F) and (G) if it is enabled, 0 – 121. Sets the color code of an
digital channel, 0 – 15.
• Output power (if activated)
The Power feature controls the power level of the radio trans-
mitter. There are three output power levels; low, medium, and
high. The low setting will reduce the communication range
but will increase the battery life.
• Reset
Press plus button for 2 seconds to reset the headset to its
default state.
SMART TIP: When browsing long lists such as channel and
sub channel, press and hold either the [+] or [–] button to skip
ten items at the time.
SMART TIP: The headset will automatically exit the menu
after 10 seconds. Or, simultaneously press and hold the [+]
and [–] buttons for two seconds. A beep will confirm the menu
has been exited.
FP3806_rev_a.indd 5
4.6 Two-Way Radio Communication
Select the appropriate two-way radio channel using the
menu. To transmit a two-way radio message, press and hold
the Push-To-Talk (PTT) button. If VOX is activated, speak into
the microphone to transmit.
SMART TIP: Your dealer can set the time for maximum
transmission time.
SMART TIP: Double press on the PTT button to activate or
deactivate VOX.
To maintain noise cancelling performance, the speech
microphone should be positioned very close to your mouth
(less than 3 mm or 1/8 inch).
4.7 Bluetooth
4.7.1 Pairing a Bluetooth
When the headset is powered on, press and hold the BT
button on the left cup for two seconds to enter pairing mode
connected com- when no device is paired. A voice message will confirm
®
"Bluetooth
Make sure that Bluetooth
device. Scan for devices and select "WS LiteCom Pro III
Headset". A voice message will confirm when the pairing is
complete "Pairing complete".
The headset can be paired to 2 Bluetooth
be connected to two devices at the same time
NOTE: By default, the radio VOX functionality is disabled
when taking a phone call via a Bluetooth
the call has ended VOX is automatically back on. To transmit
on the two-way radio during phone call, press the PTT button.
If the PTT button is pressed during a phone call, your voice
will only transmit through the two-way radio and not to the
phone call. To activate VOX during a phone call, double press
the PTT button. Your voice will then be transmitted to both the
two-way radio and the phone call.
5
Wireless Communication
®
device
®
pairing on".
®
is activated on your Bluetooth
®
devices, and can
®
connection. Once
®
®
2017-01-25 09:40:00