3M PELTOR WS ALERT MRX21AWS6 Series Manual page 12

GB
Connected to phone and two-way radio.
Operating phone. (see fig. 7).
Bluetooth
®
State
button
Incoming call
Outgoing call/Call
in progress
Ongoing reception
on two-way radio
Short press
and incoming call
Ongoing phone
call and reception
on two-way radio
Incoming call
Long press
Call in progress
NOTE: When connected to a two-way radio you cannot
control the audio playback unit from the headset.
NOTE: If you have an ongoing phone call, you will get a note
"Beep-Beep" for incoming call on the two-way radio. To switch
to the incoming two-way radio call, short press (1 s) the the
Bluetooth button [ ] to end the call. Short press (1 s) the
®
Bluetooth button [ ] one more time to listen to the two-way
®
radio or wait for next incoming two-way radio message.
NOTE: Communicate via Bluetooth
To maintain noise cancelling performance, the speech
microphone should be positioned very close to your mouth
(less than 3 mm or 1/8 inch).
DID YOU KNOW: The headset supports Bluetooth
streaming A2DP 1.3 from different apps or from the phone's
media player.
DID YOU KNOW: Audio playback will be automatically
paused from audio playback unit when you have a call in
progress or two-way radio message. After end call / message
the audio playback will automatically start again.
SMART TIP: If the headset has been reset to factory default,
it automatically enters pairing mode the first time the headset
is powered on again.
5
Action
Answer
End call
Answer
End call
Reject
Toggle call between
phone/headset
G:1
®
®
Bluetooth 4.2
®
Bluetooth is a global wireless communication standard that
®
connects devices together over a certain distance. Think
headset and phone, speaker and PC to smartphone and
more. Read more on www.bluetooth.com
Bluetooth profiles HSP 1.2, HFP 1.6, A2DP 1.3, AVRCP 1.6
®
More info on https://www.bluetooth.org/tpg/listings.cfm
Configuring your headset (fig. 11)
Long press (2 s) the Menu button [M] to access the
configuration menu. A voice message will confirm "Menu".
Short press (1 s) the Menu button [M] to navigate through the
menu. A voice message will confirm each menu step. Short
press (1 s) the [ + ] or [–] button to activate/deactivate/change
different configurations.
The following options exists in the configuration menu:
1. Bluetooth pairing (fig. 6)
®
When the voice message says "Bluetooth
press (1 s) the [ + ] button to start pairing. Short press (1 s) the
[–] button to stop pairing. A voice message will confirm
pairing on". Search and select "WS Alert XPI" on
"Bluetooth
®
your Bluetooth device. A voice message will confirm when
®
pairing is complete "Pairing complete" and "Connected". Short
press (1 s) the [–] button to stop the pairing. A voice message
will confirm, "Pairing off".
2. Bass boost
Bass boost gives a fuller bass sound to streamed stereo
music. Short press (1 s) the [ + ] or [–] button to enable/disable
bass boost.
3. Surround balance
Short press (1 s) the [–] button will increase left side and
reduce right side. Short press (1 s) the [ + ] button will increase
right side and reduce left side. A voice message will notify
when the surround balance is centered, "Center".
4. Surround equalizer
Surround equalizer changes the frequency characteristics of
the surround sound. Short press (1 s) the [–] or [ + ] button to
change the surround equalizer levels, "Low – Normal – High
– Extra high".
5. Sidetone volume
Sidetone is audible feedback to the headset user during
during a conversation. Short press (1 s) the [–] or [ + ] button
to change the sidetone volume, "Off – Low – Normal – High".
6. Battery type
Short press (1 s) the [–] or [ + ] button to change the battery
type to either rechargeable or alkaline.
7. Reset to factory default (fig. 12)
Short press (1 s) the [–] or [ + ] button, then long press (2 s)
the Menu button [M]. A voice message will guide you.
pairing", short
®