Table of Contents
Advertisement
You can use this to reset the Common LFO and Common
Step Sequencer. For instance, to create an effect similar to
the per-voice LFO and Step Sequencer's Key Sync Off
setting, use Gate 1 + Damper as the reset source.
Gate2 and Gate2+Damper
Gate 2 is similar to Gate 1, but it triggers with every new
note-on, even in the middle of a legato phrase.
Gate2+Damper includes the damper pedal in the equation, as
shown in the diagram below.
Note: When used as a reset controller for Common LFO and
Common Step Sequencer, Gate2 and Gate2+Damper will
have the same effect.
1
2
1
2
N ote
Damper Ped al
G ate1
G ate1 +Dmpr
G ate2
G ate2 +Dmpr
HD-1
The HD-1 supports all of the "Physical and MIDI
controllers," as described on page 1109, in addition to the
AMS sources below.
AMS Mixer1&2
These are the outputs of the oscillator's AMS Mixers. For
more information, see "6–1: OSC 1 AMS Mixer" on
page 102.
Wave Seq AMS Out1&2
These are the modulation outputs of the oscillator's Wave
Sequence. For more information, see "Modulating Program
parameters per step" on page 189 of the Operation Guide.
Pitch EG
This is the output of the Pitch EG, which is shared between
both oscillators. For more information, see "2–9: Pitch EG"
on page 69.
Filter EG
This is the output of the oscillator's Filter EG. For more
information, see "3–4: Filter1 EG" on page 81.
Amp EG
This is the output of the oscillator's Amp EG. For more
information, see "4–3: Amp1 EG" on page 91.
LFO1 &2
These are the outputs of the oscillator's two LFOs. For more
information, see "5–1: OSC1 LFO1" on page 96.
Common LFO
This is the output of the Common LFO, which is shared by
all voices of both oscillators. For more information, see "5–
9: Common LFO" on page 100.
Alternate Modulation Sources (AMS) Alternate Modulation Source (AMS) List
G ate1, G ate1 +Damper,
G ate2, G ate2 +Damper
3
3
Dmpr
O n
O ff
Reset
C ontroller
Time
Filter Key Track
This is the output of the oscillator's Filter Key Track
generator. For more information, see "3–2: Filter1
Modulation" on page 76.
Amp Key Track
This is the output of the oscillator's Amp Key Track
generator. For more information, see "4–2: Amp1
Modulation" on page 88.
Common Key Track1&2
These are the outputs of the two Common Key Track
generators, which are shared between both oscillators. For
more information, see "6–9: Common Keyboard Track" on
page 109.
EXi Common
EXi programs support all of the "Physical and MIDI
controllers," as described on page 1109, in addition to the
AMS sources below, plus any AMS sources provided by the
specific EXi instruments.
Common Step Seq
This is the output of the Common Step Sequencer, which is
shared by all voices of both EXi. For more information, see
"5–1: Common Step Seq" on page 184.
Common LFO
This is the output of the Common LFO, which is shared by
all voices of both EXi. For more information, see "5–2:
Common LFO" on page 187.
Common Key Track1&2
These are the outputs of the two Common Key Track
generators, which are shared between both EXi. For more
information, see "5–2: Common LFO" on page 187.
EXi AL-1
The AL-1 supports all of the "EXi Common" AMS sources,
in addition to the AMS sources below.
AMS Mixer1&2
These are the outputs of the two AMS Mixers. For more
information, see "6–1: OSC 1 AMS Mixer" on page 102.
Step Sequencer
This is the output of the per-voice Step Sequencer. For more
information, see "8–1: Step Sequencer" on page 221.
EG1 (Filter), EG2 (Pitch), and EGs 3 & 4
These are the outputs of the four assignable EGs. For more
information, see "7–1: EG 1 (Filter)" on page 217.
Amp EG
This is the output of the dedicated Amp EG. For more
information, see "6–3: Amp EG" on page 214.
LFO1 ...4
These are the outputs of the four assignable LFOs. For more
information, see "8–2: LFO 1" on page 223.
1111
Advertisement
Table of Contents
