Options; Ecm Rx; Incoming Ring; Remote Rx - Canon imageCLASS D1370 Basic Operation Manual

Options

Configure the following options to receive a fax.
Fax Settings
" ECM RX" (→P. 6-25)
RX
"Incoming Ring" (→P. 6-25)
Function
"Remote RX" (→P. 6-25)
Settings
"Auto RX Switch" (→P. 6-25)
" 2-Sided Printing" (→P. 6-25)
RX Print "Reduce RX Size" (→P. 6-26)
Settings
" RX Page Footer" (→P. 6-26)
" Continue Printing When Toner Is Low" (→P. 6-26)

ECM RX

The ECM (Error Correction Mode) detects and corrects
errors that occur during fax transmissions. It helps in
minimizing sending errors caused by a poor connection.
NOTE
Check if the ECM is enabled on the receiving fax
machine
The ECM is effective only when it is enabled on both machines.
An error occurs even when the ECM is enabled
The error may be caused by poor telephone line conditions.
When telephone line conditions are poor
It may take additional time to receive your fax if a problem occurs
when sending over the telephone line.
How to access the option
[ ] (Menu) → <Fax Settings>→ <RX Function
Settings> → <ECM RX>
Settings
(Bold: Default setting)
Off Disable the ECM.
On
Enable the ECM.

Incoming Ring

Specify whether or not the external telephone or the
handset rings on an incoming call when <RX Mode> is set
to <Auto> or <Fax/Tel Auto Switch>.
You can set the incoming call ring time.
The machine automatically starts receiving a fax after the
external telephone keeps ringing for a specified length of
time.
The machine's speaker rings on an incoming fax only when
<RX Mode> is set to <Fax/Tel Auto Switch>.
How to access the option
[ ] (Menu) → <Fax Settings> → <RX Function
Settings> → <Incoming Ring>
Settings
(Bold: Default setting)
The telephone does not ring on an
Off
incoming call.
Ring Times: The telephone rings on an incoming call.
On 1 to 2 to 99 You can set the incoming call ring time in
(times) rings in <Ring Times>.

Remote RX

Specify whether to receive faxes remotely by dialing the ID
number using the push-buttons of the external telephone
connected to the machine when an incoming call comes.
If you use the pulse line, press "*" (tone) and then dial the
Remote RX ID.
How to access the option
[ ] (Menu) → <Fax Settings> → <RX Function
Settings> → <Remote RX>
Settings
(Bold: Default setting)
Off Disable remote retrieval.
Remote RX Enable remote retrieval.
On
ID: 00 to 25 You can specify the ID number in <Remote
to 99 RX ID>.

Auto RX Switch

Set the incoming call ring time before the machine switches
to the fax mode automatically. This option can be enabled
when the <RX Mode> is set to <Manual>.
How to access the option
[ ] (Menu) → <Fax Settings> → <RX Function
Settings> → <Auto RX Switch>
Settings
(Bold: Default setting)
The machine does not switch to the fax
Off
mode automatically.
Incoming
The machine switches to the fax mode
Ring Time: 1
On automatically after the specified length
to 15 to 99
of time.
(seconds)

2-Sided Printing

Enable this option to print on both sides of paper. This saves
excessive paper consumption.
IMPORTANT
Notes on 2-Sided printing
Accurately attach the paper size switch lever. If the paper size
switch lever is not securely attached, documents may not
be fed properly or jammed.
"1-sided Printing and 2-sided Printing" (→P. 4-4)
How to access the option
[ ] (Menu) → <Fax Settings> → <RX Print Settings>
→ <2-Sided Printing>
Settings
(Bold: Default setting)
Off
Print on only one side of paper.
On Print on both sides of paper.
6-25