Table of Contents
Advertisement
Quick Links
Groomer Brush Kit
ProStripe 560 Mower
Model No. 134-3722
Safety
Safety and Instructional
Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
134-3990
Register at www.Toro.com.
decal134-3990
Form No. 3431-222 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3431-222* A
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 134-3722
Summary of Contents for Toro 134-3722
- Page 1 Form No. 3431-222 Rev A Groomer Brush Kit ProStripe 560 Mower Model No. 134-3722 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Brush-adjustment bracket Groomer brush Capscrew (8 x 60 mm) Washer (8 mm) Locknut (8 mm) Brush-height plate Carriage bolt (8 x 25 mm) Assemble the brush mount. - Page 3 Disconnect the spark-plug wire from the spark Assemble the brush-adjustment bracket to the plug; refer to the Operator’s Manual for your groomer brush (Figure 1) with 4 capscrews (8 machine. x 60 mm), 8 washers (8 mm), and 4 locknuts (8 mm).
- Page 4 g284578 Figure 4 1. Capscrew (6 x 20 mm) 4. Tab (brush mount) 2. Strut (brush) 5. Locknut (6 mm) 3. Washer (6 mm) Secure the brush strut to the brush mount (Figure 4) with a capscrew (6 x 20 mm), 2 g284575 Figure 3 washers (6 mm), and a locknut (6 mm).
-
Page 5: Removing The Wheels
Assembling the Brush Kit to the Machine Parts needed for this procedure: Lower brush bracket Self-tapping, flange-head screw (6 x 20 mm) g283871 Capscrew (6 x 20 mm) Figure 6 Washer (6 mm) Locknut (6 mm) Remove the 7 self-tapping, flange-head screws (6 x 20 mm) that secure the front fins to the supports of the mower deck, and remove the Removing the Wheels... - Page 6 Assembling the Lower Brush Assembling the Groomer Brush to Brackets to the Machine the Lower Brush Brackets Align the holes in the lower brush bracket with Assemble a capscrew (6 x 20 mm) and washer the holes in the groomer brush support of the (6 mm) through the hole in the brush mount mower deck as shown in Figure...
- Page 7 Tighten the capscrews and locknuts. Mark the hole location of the brush strut onto the deck (Figure 12). Move the strut up and centerpunch the midpoint of the mark that you made in step 2. Drill the centerpunch mark with a 6.5 mm drill (Figure 12).
- Page 8 Drilling the Deck for the Left Brush Assembling the Left Brush Strut Strut to the Machine At the left side of the mower deck, align the Align the hole in the brush strut with the hole in brush strut 90° to the to the brush mount (Figure the deck (Figure...
- Page 9 Finishing the Kit Installation. No Parts Required Procedure g285247 Figure 16 Add fuel to the fuel tank; refer to the Operator’s Manual for your machine. 1. Support (front fin—mower 3. Self-tapping, flange-head deck) screw (6 x 20 mm) 2. Front fins Assemble the front fins to the mower deck (Figure 16) with the 7 self-tapping, flange-head...
-
Page 10: Operation
Adjusting the Brush Height Operation Loosen the knobs at the sides of the brush mount (Figure 19). Adjusting the Brush Angle Loosen the knobs at the sides of the brush mount (Figure 18). g284762 Figure 18 1. Knob Use the handle of the brush-adjustment bracket to adjust the angle of the groomer brush (Figure g284761... -
Page 11: Maintenance
Maintenance Replacing the Brush Remove the 4 capscrews (8 x 60 mm), 8 washers (8 mm), and 4 locknuts (8 mm) that secure the groomer brush to the brush-adjustment bracket, and remove the brush (Figure 20). g284816 Figure 20 1. Capscrew (8 x 60 mm) 4.