Table of Contents
Advertisement
Fan Installation
H35U-NG / LP AND H35S-NG / LP
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged (grounding) plug for
H35U-NG / LP AND H35S-NG / LP
your protection against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug.
INSTALLING THE OPTIONAL FAN
Fan Kit Contains:
Figure 9
Qty
Description
1
Fan Speed Controller with nut and knob
1
Fan Assembly with green ground wire attached
1
Power Cord
1
Plastic Wire Strain Relief Grommet
1
Plastic Cable Tidy Clip
1. Remove the Top Control Panel assembly by removing the 3 screws, and
install the fan speed controller onto the control panel and secure with
nut. Connect the two fan speed controller wires to the two available wire
connectors.
Figure 10
Removing the Fan
1. Unplug or disconnect power source to stove.
2. Reinstall the Top Control Panel assembly with the 3 screws, and push
2. Reverse steps 7 to 10 from "Installing the Optional Fan" instructions
black control knob onto fan speed controller.
above.
Servicing the Thermodisc
To replace or service the fan thermodisc (temperature switch), use the
following steps:
1. Unplug or disconnect power source to stove.
2. Remove two screws from the lower left and lower right areas of the
back cover panel.
Figure 2
3.Remove the rear fan access panel by removing the 6 screws.
Figure 11
4. Install the power cord onto the unit. Pass the end of the cable through
the hole in the back cover panel, leaving about 8 inches of cable inside
the unit. Clamp the plastic wire strain relief grommet onto the power cord
and push it into the hole from the outside to secure the cord in place.
920-450
Figure 5
5. Secure power cord ground wire (green) to ground lug as shown in Fig 9.
Hampton® H35U Direct Vent Freestanding Gas Stove
920-450
H35U-NG / LP AND H35S-NG / LP
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged (grounding) plug for
your protection against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug.
Figure 9
Figure 1
Removing the Fan
1. Unplug or disconnect power source to stove.
2. Reverse steps 7 to 10 from "Installing the Optional Fan" instructions
above.
Servicing the Thermodisc
To replace or service the fan thermodisc (temperature switch), use the
Figure 3
following steps:
1. Unplug or disconnect power source to stove.
2. Remove two screws from the lower left and lower right areas of the
back cover panel.
Figure 12
Figure 4
Figure 11
2
920-450
3. Lift the back cover panel up and pivot out away from the
unit. Take care note to pull on the wires attached to the
back cover panel.
6. Connect the black wire with male connector from the power cord
to the black wire with female connector from the unit.
Figure 13
4.The thermodisc can now be accessed on the back of the
firebox behind the air intake tube. (Image 14)
7. Secure green ground wire from fan assembly to ground lug as
Figure 14
shown in Fig 9.
8. Install fan into unit by aligning the two rubber grommets on the
NOTE: When servicing the thermodisc ensure you do not
fan assembly with the two upright pins on the unit and lowering
damage the air intake flex tubes.
into place to secure.
Figure 10
9. Connect the white wire from the unit and the remaining black
wire from the power cord to the two connector pins on the fan
assembly. Tidy excess length of ground wire using the supplied
plastic cable tidy clip.
H35U-NG / LP AND H35S-NG / LP
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged (grounding) plug for
your protection against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do not cut or remove
Figure 8
the grounding prong from this plug.
10. Reinstall the rear fan access panel with 6 screws to complete
installation.
NOTE: When power cord is plugged in, speed control is in the
ON position and stove is burning, allow 10-15 minutes for the
thermodisc (temperature switch) to activate and turn on the fan
Figure 9
automatically.
Figure 12
Removing the Fan
1
1. Unplug or disconnect power source to stove.
Figure 9
Figure 6
Figure 7
10.20.21
2
Figure 10
10.20.21
installation
3. Lift the back cover panel up and
unit. Take care note to pull on t
back cover panel.
Figure 13
4.The thermodisc can now be acce
firebox behind the air intake tube
Figure 14
NOTE: When servicing the therm
damage the air intake flex tubes.
3. Lift the back cover panel up a
unit. Take care note to pull o
back cover panel.
Figure 1
4.The thermodisc can now be ac
firebox behind the air intake tu
Figure 10
Figure 1
NOTE: When servicing the the
damage the air intake flex tubes
15
Advertisement
Table of Contents
