Table of Contents
Advertisement
installation
3) Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4) Attach the adjustable pipe section to the vent
terminal using Mill-Pac and/or high temperature
silicone and attach with 3 of the #8 x 1/2" screws
(stainless steel).
NOTE: For best results and optimum perfor-
mance with each approved venting sys-
tem, it is highly recommended to apply
"Mill-Pac" sealant (supplied) to every
inner pipe connection. Failure to do so
may result in drafting or performance
issues not covered under warranty.
Silicone (red RTV) is optional.
Note: The pipe seam should be facing down.
Note: To make the installation more aestheti-
cally pleasing, we recommend framing
out a square that the cap can be mounted
on.
26
Note: If installing termination on a siding
covered wall, a vinyl siding standoff or
furring strips must be used to ensure that
the termination is not recessed into the
siding. For vinyl siding standoff installa-
tion refer to the Dura-Vent Termination
instructions.
i d e W
O u t s
Furring
Strips
5) Slide the partially connected pipe and vent
terminal assembly through the wall thimbles
(from the exterior into the interior) and secure
the cap to the exterior wall with 4 of the sup-
plied screws (#8 x 1-1/2" drill point, stainless
e x t é
steel). Note: pilot holes will need to be drilled
M u r
through the wall thimble on all 4 corners.
Note: The four screws provided for the vent
Fourrures en bois
cap should be replaced with appropriate
fasteners for stucco, brick, concrete, or
other types of sidings.
6) A bead of non-hardening mastic should be run
around both the termination and vinyl siding
standoff to prevent water from entering and
to make a tight seal between the cap and the
standoff.
7) Stretch the 4" dia. flex liner out fully and get a
trial fit of the liner onto the 4" dia. starter collar.
8) Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length, this will
make the final assembly easier to work with.
9) Secure the 4" dia. flex liner to the 4" adaptor with
Mill-Pac and 3 of the #8 x 1/2" screws (stainless
steel).
10) Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8 x
1-1/2" drill point, black) to the wall.
11) Slide the 90
elbow and the 4 ft. pipe section (crimp end up)
over the 4" dia. flex liner.
12) Install the spring spacers onto the pipe sections.
13) Secure the 4" dia. flex liner with adaptor onto
the stove collar. Put a bead of Mill-Pac around
the appliance adaptor and secure with 3 screws
(#8 x 1/2, stainless steel).
14) Attach the 45
sealing with Mill-Pac and/or high temperature
silicone and securing with 3 of the #8 x 1/2"
(black) screws.
15) Attach the pipe section to the 45
sealing with Mill-Pac and/or high temperature
silicone and securing with 3 of the #8 x 1/2"
screws (black). Pipe seams should be facing
the wall.
16) Attach the 90
a l l
sealing with Mill-Pac and/or high temperature
Furstrp.eps
silicone and securing with 3 of the #8 x 1/2"
see also c34020a.eps
screws (black).
17) Slide the adjustable pipe section onto the 90
elbow. Slide the trim collar over the adjustable
pipe sections to cover the joint of the telescopic
section.) The flex may have to be compressed
back in order for the adjustable pipe to properly
mate to the elbow. Seal with Mill-Pac and/or
high temperature silicone and secure with 3 of
r i e u r
the #8 x 1/2" screws (black). Pipe seams facing
furstrpf.eps
down.
french
18) Install the trim collar over the starter collar and
secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only Stove
Brite High Temperature Metallic Black Stove Paint.
Hampton® H35U Direct Vent Freestanding Gas Stove
elbow (crimp end up), the 45
o
o
elbow onto the starter collar by
elbow by
o
elbow onto the pipe section by
o
o
o
Advertisement
Table of Contents
