Abbreviations and Explanations, 4
Alarm (Trip) Output Contacts, 37
Attach to Network Device Control, 44
Automatic Soft Stop Amps Threshold, 47
Auto. Restart After Power Failure, 38
Before Initial Start-Up, 48
Capacity Override, 36
Chilled Water Recycle Mode, 47
Chiller Control Module (CCM), 88
Chiller Familiarization, 5
Chiller Information Nameplate, 5
Chiller Operating Condition (Check), 65
Chiller Tightness (Check), 48
Compressor Bearing and Gear Maintenance, 74
Condenser, 5
Condenser Freeze Prevention, 38
Condenser Pump Control, 37
Control Algorithms Checkout Procedure, 77
Control Panel, 5
Control Modules, 87
Control Test, 77
Controls, 10
CVC/ICVC Operation and Menus, 15
Cooler, 5
Default Screen Freeze, 35
Definitions (Controls), 10
Demand Limit Control Option, 39
Design Set Points, (Input), 55
Details (Lubrication Cycle), 8
Display Messages (Check), 76
Equipment Required, 48
Evaporator Freeze Protection, 38
Extended Shutdown (Preparation for), 66
Factory-Mounted Starter or Variable Frequency Drive, 7
General (Controls), 11
Guide Vane Linkage (Check), 72
Heat Exchanger Tubes and Flow Devices (Inspect), 74
High Discharge Temperature Control, 36
Ice Build Control, 43
Centrifugal Liquid Chiller, CL-1
Integrated Starter Module (ISM), 88
Introduction, 4
Job Data Required, 48
Kilowatt Output, 37
Lead/Lag Control, 40
Leak Test Chiller, 50
Local Occupied Schedule (Input), 55
Local Start-Up, 46
Lubrication Cycle, 8
Lubrication System (Check), 72
INDEX
Motor and Lubricating Oil Cooling Cycle, 7
Motor-Compressor, 5
Motor Rotation (Check), 65
Notes on Module Operation, 87
Oil Cooler, 36
Oil Pressure and Compressor Stop (Check), 65
Oil Reclaim System, 8
Oil Sump Temperature Control, 36
Open Oil Circuit Valves, 48
Optional Pumpout Compressor Water Piping (Check), 53
Compressor (Check), 63
Optional Pumpout System Maintenance, 75
Ordering Replacement Chiller Parts, 75
Overview (Troubleshooting Guide), 76
Physical Data, 90
PIC II System Components, 11
PIC II System Functions, 33
Power Up the Controls and Check the Oil Heater, 55
Preparation (Initial Start-Up), 64
Preparation (Pumpout and Refrigerant Transfer
Pressure Transducers (Check), 75, 76
Prevent Accidental Start-Up, 65
Ramp Loading, 36
Refrigerant Float System (Inspect), 74
Refrigerant Leak Detector, 37
Refrigerant Properties, 71
Refrigerant (Removing), 71
Refrigerant Tracer, 48
Refrigeration Cycle, 7
Relief Valves (Check), 53
Relief Valves and Piping (Inspect), 74
Remote Reset of Alarms, 37
Remote Start/Stop Controls, 36
Repair the Leak, Retest, and
Apply Standing Vacuum Test, 72
Replacing Defective Processor Modules, 88
Running System (Check), 66
Safety and Operating Controls (Check Monthly), 73
Safety Considerations, 1
Safety Controls, 34
Safety Shutdown, 47
Service Configurations (Input), 55
Service Operation, 45
Shipping Packaging (Remove), 48
Shunt Trip (Option), 35
Shutdown Sequence, 47
Solid-State Starters, 88
Spare Safety Inputs, 36
Standing Vacuum Test, 50
Starter (Check), 54
Starting Equipment, 9
Starting Equipment (Inspect), 75
123