Page 4
■ 製品の呼び方 製品名称 本文中の表記 LTO4 PG-LT401/PGBLT401/PGBLT401C ® ® Microsoft Windows Server 2008 Standard ® ® Microsoft Windows Server 2008 Enterprise ® ® Microsoft Windows Server 2008 Standard without Hyper-V ® ® Microsoft Windows Server 2008 Standard without Windows Server 2008 Hyper-V 64-bit ®...
デバイスドライバのインストール Windows Server 2003 Windows Server 2008 Linux 本製品と接続する SAS カードのドライバは、 SAS カードのマニュアルを参照してイ ンストールしてください。 3.3.1 デバイスドライバのインストール(PRIMERGY FT モ デル以外に搭載の場合) Administrator Windows 「ハードウェア」タブを選択し、 [デバイスマネージャ]をクリックします。 QUANTUM ULTRIUM 4 SCSI Sequential Device Windows Update A:\LTO4HH PRIMERGY [CD/DVDドライブ]:\DRIVERS\tape\LTO4HH 3 サーバ本体への搭載と導入方法 ...
Page 18
Quantum LTO 4 Tape Drive 3.3.2 デバイスドライバのインストール(PRIMERGY FT モ デルに搭載の場合) ■ 注意事項 Virtual Server CoServer オ ■ Windows Server 2003 の場合(Windows Server 2003 x64 は含みま せん) FT1 FT2 CoServer Online Administrator CoServer1 Quantum LTO 4 Tape Drive Windows Update...
Page 19
DVD-ROM A:\LTO4HH Temp C:\Temp\LTO4HH Virtual Server Virtual Server Virtual Server Quantum LTO 4 Tape Drive Virtual Server Virtual Server 3 サーバ本体への搭載と導入方法 ...
Page 20
Fujitsu Tape Maintenance Advisor for Windows [CD/DVDドライブ]:\PROGRAMS\Japanese\TmAdvisor\TMAdoc Tape Maintenance Advisor は、弊社のインターネット情報ページ (http://primeserver.fujitsu.com/primergy/)内に最新版が登録されています。 『ダウンロード』→『ダウンロード検索』で、サーバの製品名および型名を選択し、カテ ゴリに「添付ソフト」を指定して検索してください。 ■ Linux の場合 Tape Maintenance Advisor for Linux Tape Maintenance Advisor for Linux http://primeserver.fujitsu.com/primergy/ Fujitsu Tape Maintenance Advisor for Linux V3.0 tar.gz Linux Windows tar xvfz ファイル名.tar.gz...
Page 21
Linux RHEL-ES4(x86)/RHEL-AS4(x86)/ RHEL-ES4(EM64T)/RHEL-AS4(EM64T) TmAdvisor/forv4/TmAdvisor/TMA RHEL 5(x86)/RHEL 5(Intel 64) TmAdvisor/forv5/TmAdvisor/TMA Fujitsu Tape Maintenance Advisor for Linux TmAdvisor/TMAdoc 3.4.2 インストール方法 ■ Tape Maintenance Advisor for Windows Administrator PRIMERGY [CD/DVDドライブ]:\PROGRAMS\Japanese\TmAdvisor\Setup.exe readme.txt ■ Tape Maintenance Advisor for Linux Linux RHEL-ES4(x86)/RHEL-AS4(x86)/ RHEL-ES4(EM64T)/RHEL-AS4(EM64T) TmAdvisor/forv4/TmAdvisor/TMA/Installer.bat RHEL 5(x86)/RHEL 5(Intel 64) TmAdvisor/forv5/TmAdvisor/TMA/Installer.bat...
Page 22
バックアップジョブの設定(自動排出の設定) ■ CA ARCserve Backup の場合 ■ Windows Backup の場合(Windows Server 2003) (*1) 例:rsm refresh /lf"Quantum LTO 4 Tape Drive" rsm eject /lf"Quantum LTO 4 Tape Drive"/astart Windows Server 2003 @echo off setlocal rsm inventory /lf"Quantum LTO 4 Tape Drive" /aFULL timeout /t 60 rsm refresh /lf"Quantum LTO 4 Tape Drive"...
Page 24
デバイスドライバおよびバックアップソフト ウェアの設定・注意事項 2008 ■ Windows 用デバイスドライバについて Windows http://primeserver.fujitsu.com/primergy/ ■ バックアップソフトウェアについて バックアップソフトウェア (*) Windows Server 2008 CA ARCserve Backup r12 (*) Windows Server 2003 CA ARCserve Backup r12 Windows Backup (*) RHEL-ES4(x86)/ NetVault8 RHEL-AS4(x86) (*) RHEL-ES4(EM64T)/ NetVault8 for EM64T RHEL-AS4(EM64T) (*)...
Page 25
Windows Server 2003 CA ARCserve Backup オ ARCserve Backup CA ARCserve Backup オ ■ ASR(Automated System Recovery)に関する注意事項 Windows Server 2003 Windows Automated System Recovery C Windows Automated System Recovery P.49 ■ Windows 自動システム回復(ASR)使用時および CA ARCserve Backup の Disaster Recovery Option 使用時に、フロッピーディスク ドライブ(USB)を使用する場合について...
Page 47
地 オ 把握 ? 果 果 製品概要 ■ 製品名 Fujitsu Tape Maintenance Advisor for Windows Fujitsu Tape Maintenance Advisor for Linux ■ 動作環境 - Windows Windows Server 2008 Windows Server 2003/Windows Server 2003 x64 - Linux RHEL-ES4(x86)/RHEL-AS4(x86)/RHEL-ES4(EM64T)/RHEL-AS4(EM64T) RHEL 5(x86)/RHEL 5(Intel64)
付録 C Windows 自動システム回復 (Automated System Recovery)について Windows 自動システム回復ディスクについて Windows Server 2003 Windows Automated System Recovery Windows Windows ■ デバイスドライバの追加 Windows 以降の作業は、隠しファイルやフォルダを含めた、すべてのファイルやフォルダが表示さ れている必要があります。また、ファイルの拡張子を表示させてください。 フォルダはコピーしないでください。 Windows Server 2003 Windows Server 2003 x64 付録 C Windows 自動システム回復(Automated System Recovery)について ...
Page 50
asr.sif ノ パ 帳 む INSTALLFILES asr.sif "DISKS.GPT" Windows Server 2003 Windows Server 2003 x64 パ winnt.sif ノ パ 帳 白 winnt.sif む...
Page 51
Windows Server 2003 Windows Server 2003 x64 付録 C Windows 自動システム回復(Automated System Recovery)について ...
Page 52
Windows 自動システム回復(ASR)の使用方法 ■ 事前に準備すること Windows 標準ではないドライバ(例:RAID ドライバ、SAS ドライバなど)が必要な場合に は、ASR を実施する前に次の準備を行ってください。 Windows 720KB 別途 FDD ユニット(USB)を使用する場合の注意事項は、 「3.7 デバイスドライバおよび バックアップソフトウェアの設定・注意事項」の「■ Windows 自動システム回復 (ASR)使用時および CA ARCserve Backup の Disaster Recovery Option 使用時に、 フロッピーディスクドライブ(USB)を使用する場合について」 (→ P.25)を参照 してください。...
Page 53
■ ASR の使用方法 Windows Server 2003 Windows Server 2003 Windows 標準ではないドライバ(例:RAID ドライバなど)が必要な場合には、 画面の下部に「Press F6 if you need install a third party SCSI or RAID driver …」 とメッセージが表示されます。その場合は、 【F6】キーを押してください。 この メッセージは約 5 秒間しか表示されませんので注意してください。 Press F2 to run Automated System Recovery(ASR) … P.52 Enter 終...
Page 55
Before Reading This Manual Thank you for purchasing the Fujitsu Tape Drv LTO4 Ultrium4/Ultrium3/Ultrium2 800GB (PG- LT401/PGBLT401/PGBLT401C). This manual explains the basic usage of the Tape Drv LTO4 Ultrium4/Ultrium3/Ultrium2 800GB (hereafter referred to as "this product"). Before using this product, read this manual in order to ensure proper use.
Page 56
Remarks Warning Descriptions Various symbols are used throughout this manual. These are provided to emphasize important points for your safety and that of others. The symbols and their meanings are as follows. Make sure to fully understand these before reading this manual. Ignoring this symbol could be potentially lethal.
Page 57
Abbreviations The following expressions and abbreviations are used to describe the product names used in this manual. Product names Expressions and abbreviations Tape Drv LTO4 Ultrium4/Ultrium3/Ultrium2 800GB this product, tape device (PG-LT401/PGBLT401/PGBLT401C) ® ® Microsoft Windows Server 2008 Standard ® ®...
Page 58
Safety For safe use of this product, it is vital that the following warnings are heeded. Handling this product WARNING • Keep the plastic bags used as packing, out of the reach of children. They could cause suffocation. • If a foreign object (water, pieces of metal, liquid) falls into this product, immediately turn off the server's power and unplug it from the power source.
Page 59
(*1) • Screws (x4) • Cleaning cartridge • "PRIMERGY LTO4 UNIT (PG-LT401) Device Driver for Windows" (driver floppy disk) • User's Guide (this document) *1: For custom made service (PGBLT401/PGBLT401C), items are supplied with the server. Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of Microsoft Corporation in the USA and other countries.
Feature This chapter explains the feature of this product. This product is an internal tape device that has adopted a Linear Tape Open (LTO) Ultrium4 format. This product has the following features. ・ Provides Max. 800GB data memory capacity per a tape (no compression) ・...
Component Names and Func- tions This chapter explains the component names and functions of this product. Front 3. Two-color LED 4. Segment LED 5. One-color LED 1. Front door 2. Eject button 1 Front door When inserting a data cartridge, pull the front door up. "4.3 How to Insert"(p.79) 2 Eject button Press this button to eject the data cartridge from this product.
Page 63
LED display There are three LEDs in this product, they indicate self-diagnostic tests when the power is turned on, and show status or errors during operation by using a combination of LED displays. LED display examples are as follows. " LED display specification list"(p.64) Display examples for LED are as follows.
Page 64
LED display specification list The LED combinations are as follows. For LED details, refer to "7 Troubleshooting" ( p.85). Two-color Segment One-color Status PowerOff: Power is not supplied to this product. PowerOn (No cartridge): Power is supplied and a data cartridge can On (green) –...
Rear 2. SAS connector 1. Power connector 1 Power connector Connects the power cable for the internal option in the server. "3.2 Installing and Connecting to the Server"(p.68) 2 SAS connector Connects the SAS cable for this product. "3.2 Installing and Connecting to the Server"(p.68) 2 Component Names and Functions...
How to Install and Introduce this Product to the Server This chapter explains installation and introduction of this product to the server. This product is installed and introduced to a server according to the following procedures. Steps 2 and 3 are not necessary for custom made service. Checking the setting environment.
Checking the Installation Environment For details about the server installation environment, refer to "Safety Precautions" and "Start Guide". This product is susceptible to its installation environment (especially dust) because the data recording surface is exposed inside this product. The closer to the floor, the higher the dust level is in general, so it is recommended to install this product away from the floor, such as on a desk.
Installing and Connecting to the Server For the procedure for installing this product in the server, refer to the "User's Guide" in the "PRIM- ERGY Startup Disc" provided with the server and see the description about the internal 5-inch option. For the procedure for connecting each cable, refer to the following.
Installing the Device Driver If using this product on Windows Server 2003, install the device driver according to the following procedure using the driver floppy disk provided with this product. For Windows Server 2008 and Linux, installing the device driver is not required. Refer to the SAS card's manual to install the SAS card driver that is to be connected to this product.
Click [Finish]. Click [Close]. "Quantum LTO 4 Tape Drive" is displayed under "Tape Drive". Restart the server. 3.3.2 Device Driver Installation (For PRIMERGY FT) Notes • This product can be installed only to FT1. It cannot be installed to FT2. •...
Page 71
For search and installation options, select [Search for the best driver in these locations] and set the following options. • Uncheck [Search removable media (floppy, DVD-ROM, etc.)]. • Check [Include this location in the search] and specify the folder which restored the device driver.
Setting Backup Job (Setting Automatic Ejection) When executing backup automatically, follow the procedures below to set to eject the data cartridge automatically after backup. Even when executing backup manually, make sure to eject the data car- tridge after backup. For Windows Backup (Windows Server 2003) In batch files, etc., add a description that executes the following commands after the backup commands.
When ejecting using Linux commands Add the description that executes the following command after the backup command in shell script, etc. (change /dev/st0 to suit the environment). mt -f /dev/st0 eject For NetVault Confirm the device name in the NetVault device management. In this manual, this product is referred to as "NetVaultSV:1-0.3.0_(QUANTUM_ULTRIUM_4)".
For Using FDD (USB) when Operating ASR • Notes on FDD (USB) recognition at server startup If the FDD (USB), with a floppy disk inserted, is not connected at server startup, BIOS cannot recognize the FDD (USB). During OS installation of Windows/Linux, or when executing ASR, make sure to connect the FDD (USB) with a floppy disk inserted before server startup.
Inserting/Removing the Data Cartridge This chapter explains the procedure for inserting/removing the data cartridge. Usable Data Cartridges Use the following data cartridges for this product. Product name Supplier Remarks LTO Ultrium 3 Data Cartridge FUJI PHOTO FILM Co., LTD. Storage capacity: 400GB (LTO FB UL-3 400G E) LTO Ultrium 4 Data Cartridge FUJI PHOTO FILM Co., LTD.
Handling the Data Cartridge Follow the notes below when handling the data cartridge. • Keep the data cartridge clean. • Place the data cartridge in the operation environment for at least 24 hours before using it, in order to acclimate the data cartridge to the environment. •...
4.2.2 Data Write Protection To make the data cartridge write-protected, slide the write-protect switch to the right. Write-protect switch Write-protect 4.2.3 Storing the Data Cartridge When storing the data cartridge, follow the notes below: • Make the storage area clean, and comply with the usage rules. •...
4.2.4 Checking the Condition of the Leader Pin on the Data Cartridge Check the condition of the leader pin (the pin attached to the top of the magnetic tape) on the data cartridge before use. CAUTION • Do not use defective media where a pin is detached, a cartridge is deformed, or one that has been damaged, using any such defective media can damage this product.
How to Insert Open the front door up and insert the data cartridge slowly into this product with the arrow mark facing up and the label panel facing you. When the data cartridge is fully inserted, it starts loading automatically. To avoid damaging this product and the data cartridge, note the following points.
How to Eject Check that this product is not operating (Two-color LED is blinking green). Press the Eject button. Put the ejected data cartridge in the cartridge case to store. CAUTION ・ When ejecting the data cartridge, do not stop it or push it back in. Also, do not pull out the data cartridge before it has fully ejected.
Cleaning This chapter explains cleaning for this product. Head cleaning will be performed automatically when a cleaning cartridge is inserted into this product. Cleaning takes between two to four minutes. The cleaning cartridge is ejected when cleaning operations are complete. This product uses a magnetic head to write and read data.
Timing for Magnetic Head Cleaning Perform magnetic head cleaning when the following occurs. ・ Periodical cleaning (Once every three months) ・ The LED displays "Cleaning request" Periodical cleaning Performing periodical head cleaning (approx. every three months) to prevent dust from accumulating on the head is recommended.
Cautions Concerning Backup This chapter explains the points to note about backup operations for this product. When using this product in Windows Server 2008, Windows Backup does not support backup to a magnetic tape drive. Purchase of separate backup software is required.
Page 84
Points to note during system configuration When repeatedly using a single data cartridge, all the data can be lost if the backup fails. Also, if a backup data cartridge becomes damaged, the data cannot be recovered. Damage in the event of a fail- ure can be minimized if two or more data cartridges are used for backup operation.
Troubleshooting This chapter explains the actions to be taken for each LED error display by this product and the actions to be taken when this product does not operate normally. Troubleshooting for LED display The following table indicates the status of LED display. As for error status, the troubleshooting method is described.
Page 86
LED Display Status and Action Two-color: Blinking (amber) Status Cleaning request: Needs cleaning. Segment: C Action Clean this product with a cleaning cartridge. One-color: On "5 Cleaning"(p.81) If the status does not change after cleaning, the media may be worn out. Two-color: Blinking (amber) Status Temperature abnormality is detected: The...
Page 87
LED Display Status and Action Two-color: Blinking (amber) Status Interface error Segment: 8 Action Check that the SAS cable is properly connected. If One-color: Off the status does not change, replace the SAS cable. If the problem still remains, this product or the SAS card may fail.
Page 88
Troubleshooting for operating conditions This section explains troubleshooting for when this product is not operating normally. If the problem is not resolved after performing the following troubleshooting, contact an office listed in "Appendix C Contact Information" ( p.100). For details about LED status, refer to "2.1 Front" ( p.62). Phenomenon Troubleshooting method This product does not...
Specifications This chapter describes the specifications for this product. Specifications Item Functions and Specifications Product name Tape Drv LTO4 Ultrium4/Ultrium3/Ultrium2 800GB Product ID PG-LT401/PGBLT401/PGBLT401C (*1) Data memory capacity (no compression) 800GB (When using Ultrium4 data cartridge) (*1) 400GB (When using Ultrium3 data cartridge) (*2) Data transmission rate (no compression) 114MB/s...
This product is a precision instrument and improper daily operation (cleaning/ data cartridge management/ installation environment, etc.) will lead to troubles such as backup failure. Use the following "Operation Checksheet" to prevent trouble in backup operations. The following items are recommended operations by Fujitsu. Classification Check item Description / tasks (*) ❑...
Page 91
To avoid missed backup due to year) a worn data cartridge, replacement is required for Fujitsu authorized product after one year of use or after being used 1000 times, whichever comes first. * In this case, replace the data cartridge with a new one.
Page 92
Classification Check item Description / tasks (*) ❑ Is the data cartridge The data recording surface of the data cartridge inserted right before is exposed in this product and contacts the head backup and ejected right under tension. If this situation continues for a after backup, and stored in long time, the effect of suspended particles of its case?
Page 93
Classification Check item Description / tasks (*) ❑ Is the environment of This product is susceptible to its installation this product (the server if it environment (especially dust) because the data is built in the server) dust- recording surface is exposed inside this product. free? The closer to the floor, the higher the dust level is in general, so it is recommended to install this...
Page 94
Classification Check item Description / tasks (*) ❑ When this product (the This product writes the data cartridge server if it is built in the management data when the data cartridge is server) is turned off or ejected. Therefore, if the power of the server is restarted, is the data turned off while the data cartridge is inside this cartridge ejected?
Automated System Appendix B Recovery (ASR) Automated System Recovery For Windows Server 2003, adding the device driver to the Automated System Recovery disk (A floppy disk created at system data backup for Automated System Recovery) for this product is neces- sary to use Automated System Recovery (hereafter referred to as "ASR").
Page 96
Add the following statement to the asr.sif file in the ASR floppy disk. Using a note pad, add the following four lines (including [INSTALLFILES]) to the section under "DISKS.GPT" in asr.sif file. ・ For Windows Server 2003 [INSTALLFILES] 1=1,"ASR","%FLOPPY%","QLTOx32.sys","%TEMP%\QLTOx32.sys","Quantum ",0x00000026 2=1,"ASR","%FLOPPY%","QntmLto.inf","%TEMP%\QntmLto.inf","Quantum ",0x00000026 3=1,"ASR","%FLOPPY%","qntmlto.cat","%TEMP%\qntmlto.cat","Quantum ",0x00000026 ・...
Page 97
Close all the files and check whether the following files are in ASR floppy disk. ・ For Windows Server 2003 A:\asr.sif A:\asrpnp.sif A:\LT14aX32.dll A:\QLTOx32.sys A:\qntmlto.cat A:\QntmLto.inf A:\setup.log A:\winnt.sif ・ For Windows Server 2003 x64 A:\asr.sif A:\asrpnp.sif A:\LT14aX64.dll A:\QLTOx64.sys A:\qntmlto.cat A:\QntmLto.inf A:\setup.log A:\winnt.sif By following the procedures above, the device driver of this product is added to the ASR floppy disk.
Usage of ASR This section explains the procedure for ASR usage. Prearrangement When a nonstandard Windows driver (RAID driver, SAS driver, etc.) is necessary, prepare the following before executing ASR. Create a floppy disk of a nonstandard Windows driver. For creation procedures, refer to the server's "User's Guide" or the SAS card's "User Guide". Create a driver floppy disk for an occasion when asked for a driver file in the middle of restoring ASR.
Page 99
Press [F2] key. If [F6] key was pressed at the Step 2, reading the driver is executed. 1. Insert the driver floppy disk that was created at Step 1 in " Prearrangement" ( p.98) 2. Press the [S] key as many times as necessary and read driver information. 3.
Fax: +852-2827-4724 Address: 10/F., Lincoln House, 979 King's Road Taikoo Place, Island East, Hong Kong • Indonesia: PT. Fujitsu Systems Indonesia Offices Headquarters Tel: +62-21-570-9330 (Hunting) Fax: +62-21-573-5150 Address: Wisma Kyoei Prince 10th Floor Jl. Jend. Sudirman Kav 3-4 Jakarta, Indonesia 10220 •...
Page 101
Address: Unit 802-8th floor, Fortuna Tower Hanoi 6B Lang ha Street, Ba dinh District, Hanoi Socialist Republic of Vietnam • United States: Fujitsu Computer Systems Corporation Tel: +1-800-831-3183 Fax: +1-408-496-0575 Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470 For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com). Appendix C Contact Information...
Page 103
● 落丁、乱丁本は、お取り替えいたします。 • The contents of this manual may be revised without prior notice. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. • No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.