Panasonic PT-FRQ50 Operating Instructions Manual page 121

[PROJECTOR TYPE]
[SERIAL NUMBER]
[PROJECTOR RUNTIME]
[LIGHT RUNTIME]
[CONTINUOUS LIGHTING
TIME]
[MAIN/SUB VERSION]
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[EXHAUST AIR TEMP.]
[LIGHT TEMP. 1]
*1
[LIGHT TEMP. 2]
*1
[SELF TEST]
[INPUT]
[SIGNAL NAME]
[MEMORY NO.]
[NUMBER OF REGISTERED
SIGNAL]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[ON COUNT]
[SIGNAL INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
r [DETAILED INFORMATION]
[INPUT]
[SIGNAL FORMAT]
[SIGNAL FREQUENCY]
[SYNC. STATE]
[V.SYNC WIDTH]
[SCAN TYPE]
[TOTAL DOTS]
[DISPLAY DOTS]
[TOTAL LINES]
[DISPLAY LINES]
[SAMPLING]
[SIGNAL LEVEL]
[COLORIMETRY]
[HDCP STATUS]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the projector type of the projector.
Displays the serial number of the projector.
Displays the runtime of the projector.
Displays the runtime of the light source.
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned off such as using the shutter
function.
Displays the main and sub versions of the firmware of the projector.
Displays the status of the intake air temperature of the projector.
*1
*1 Displays the status of the internal temperature of the projector.
*1 Displays the status of the exhaust air temperature of the projector.
Displays the temperature status for the front block of the light source (on the lens side).
Displays the temperature status for the rear block of the light source (on the exhaust vent side).
Displays the self-diagnosis information.
Displays the input terminal currently selected.
Displays the input signal name.
Displays the memory number of the input signal.
Displays the number of registered signals.
Displays the set cooling conditions.
[POWER ON TIMES]
[INPUT]
[SIGNAL FORMAT]
[SAMPLING]
[SIGNAL LEVEL]
[GAMMA]
[COLOR SPACE]
Displays the input terminal used for the projected image.
Displays the format of the input signal.
Displays the frequency of the input signal.
Displays the sync polarity of the input signal.
Displays the vertical sync signal pulse width of the input signal.
Displays the scan type of the input signal.
Displays the total dot count of the input signal.
Displays the number of input signal display dots.
Displays the total line count of the input signal.
Displays the number of input signal display lines.
Displays the sampling information and the color format of the input signal.
Displays the signal level of the input signal.
Displays the color gamut information of the input signal. The content of display is as follows.
[ITU-2020]: When the color gamut is compliant with ITU-R BT.2020 standard
[ITU-709]: When the color gamut is compliant with ITU-R BT.709 standard
[SMPTE 170M]: When the color gamut is compliant with SMPTE 170M standard
[---]: When there is no signal, when the color gamut information is not included in the InfoFrame information,
or when the color gamut information other than [ITU-2020], [ITU-709], or [SMPTE 170M] is included
Displays the HDCP status of the input signal. The content of display is as follows.
[HDCP2.X]: When protected with HDCP 2.2 or HDCP 2.3
[HDCP1.X]: When protected with HDCP 1.X
[NONE]: When not protected with HDCP
[---]: When there is no signal
Displays the number of times the power is turned on.
Displays the input terminal used for the projected image.
Displays the format of the input signal.
Displays the sampling information of the input signal.
Displays the signal level of the input signal.
Displays the [GAMMA] setting.
Displays the [COLOR SPACE] setting.
ENGLISH - 121