Colorimetric analyzer for total nitrogen (32 pages)
Summary of Contents for Endress+Hauser Liquiline System CA80AM
Page 1
These instructions are Brief Operating Instructions; they are not a substitute for the Operating Instructions pertaining to the device. Detailed information on the device can be found in the Operating Instructions and in the other documentation available at: • www.endress.com/device-viewer • Smart phone/tablet: Endress+Hauser Operations App...
Page 2
Liquiline System CA80AM Order code: XXXXX-XXXXXX Ser. no.: XXXXXXXXXXXX Ext. ord. cd.: XXX.XXXX.XX Serial number www.endress.com/deviceviewer Endress+Hauser Operations App A0040778 Endress+Hauser...
About this document Liquiline System CA80AM About this document Warnings Structure of information Meaning This symbol alerts you to a dangerous situation. DANGER Failure to avoid the dangerous situation will result in a fatal or serious injury. Causes (/consequences) If necessary, Consequences of non- compliance (if applicable) ‣...
Warning: Risk of injury from rotating cogwheels Documentation The following instructions complement these Brief Operating Instructions and are available on the product pages on the Internet: • Operating Instructions Liquiline System CA80AM • Device description • Commissioning • Operation • Software description (excluding sensor menus; these are described in a separate manual - see below) •...
Designated use The Liquiline System CA80AM is a wet-chemical analyzer for the almost continuous determination of the concentration of ammonium in liquid media. The analyzer is designed for use in the following applications: •...
Liquiline System CA80AM Basic safety instructions Ensure that electrical cables and hose connections are undamaged. Do not operate damaged products, and protect them against unintentional operation. Label damaged products as defective. During operation: If faults cannot be rectified: products must be taken out of service and protected against unintentional operation.
Incoming acceptance and product identification Liquiline System CA80AM Incoming acceptance and product identification Incoming acceptance Verify that the packaging is undamaged. Notify the supplier of any damage to the packaging. Keep the damaged packaging until the issue has been resolved.
Liquiline System CA80AM Incoming acceptance and product identification 3.2.2 Product identification Product page www.endress.com/ca80am Interpreting the order code The order code and serial number of your product can be found in the following locations: • On the nameplate • In the delivery papers Obtaining information on the product Go to www.endress.com.
Installation Liquiline System CA80AM 3.4.2 cCSAus The product meets the requirements as per "CLASS 2252 06 - Process Control Equipment" and "CLASS 2252 86 - Process Control Equipment". It is tested to Canada and USA standards: CAN/ CSA-C22.2 No. 61010-1-12 UL Std. No. 61010-1 (3 Edition).
Page 11
Liquiline System CA80AM Installation 417 (16.42) 530 (20.87) A0030419 2 Liquiline System CA80 open version, dimensions in mm (in) Endress+Hauser...
Page 12
Installation Liquiline System CA80AM 654 (25.74) A0028821 3 Liquiline System CA80 with base, dimensions in mm (in) Endress+Hauser...
Page 13
Liquiline System CA80AM Installation 1800 (70.9) 8 (0.31) A0041592 4 Post (accessory) for "Outdoor" version, dimensions in mm (inch) 4.1.2 Mounting location Note the following when erecting the device: ‣ If mounting on a wall, make sure that the wall has sufficient load-bearing capacity and is fully perpendicular.
Page 14
Installation Liquiline System CA80AM 4.1.3 Spacing requirements when mounting Spacing required for installing analyzer ≥330(12.99) ≤116 ° A0036774 A0036775 5 Minimum spacing required for mounting. 6 Maximum opening angle Engineering unit mm (in). Spacing required for installing wall-mount version Ø...
Liquiline System CA80AM Installation Mounting the analyzer on a wall CAUTION Incorrect installation can cause injury and damage the device ‣ If mounting on a wall, check that the analyzer is fully hooked into the wall holder unit at the top and bottom, and secure the analyzer to the upper wall holder unit using the securing screw.
Installation Liquiline System CA80AM Hook the analyzer into the wall holder unit. Secure the two top parts of the wall holder unit with the screw supplied. Installing version with analyzer stand CAUTION Incorrect installation can cause injury and damage the device ‣...
Page 17
Liquiline System CA80AM Installation A0036785 11 Securing the base Screw the base to the ground. With 2 people, lift the analyzer and fit it on the base. Use the recessed grips. Secure the base to the analyzer using the 6 screws supplied.
Installation Liquiline System CA80AM "Outdoor" version: mounting on a post 4.4.1 Erecting the post 4 x 12 (0.47) 250 (9.84) A0041437 12 Foundation plan, dimensions in mm (in) When installing outdoors, consideration must be given to providing correct protection against lightning.
Page 19
Liquiline System CA80AM Installation 4.4.2 Tool required for post mounting The following tools, which must be provided by the customer at the point of installation, are required to mount the analyzer on the post: • Open-end wrench, 17mm AF (for post retainer) •...
Page 20
Installation Liquiline System CA80AM 4.4.3 Mounting analyzer on the post A0041425 A0041426 13 Analyzer mounted on post (from front) 14 Analyzer mounted on post (from behind) Fit the clamp of the post retainer on the retaining rods and post using the nuts.
Page 21
Liquiline System CA80AM Installation Fit the counterparts and fasten the post retainer using spring washers and nuts. Mount the wall holder unit (included in the delivery with the analyzer) on the post retainer. Endress+Hauser...
Page 22
Installation Liquiline System CA80AM Insert the spacer. Screw the suspension bracket of the wall holder unit (included in the delivery with the analyzer) onto the analyzer. Endress+Hauser...
Liquiline System CA80AM Electrical connection Hook in the analyzer. Fix the upper wall holder unit in place with the screw provided. Post-installation check After mounting, check all the connections to ensure they are secure. Electrical connection WARNING Device is live! Incorrect connection may result in injury or death! ‣...
Electrical connection Liquiline System CA80AM ‣ Before establishing the electrical connection, verify that the pre-installed power cable meets the local national electrical safety specifications. Connection conditions 5.1.1 Cable types Power supply cable Power supply cable with safety plug A power supply cable is not supplied for the Cable length 4.3 m (14.1 ft)
Page 25
Liquiline System CA80AM Electrical connection Connection of analog inputs and outputs, Memosens sensors or digital fieldbuses Remove the bottle tray: Lift up the recessed grip slightly and pull it towards the front. Remove the cover that is hooked into place.
Page 26
Electrical connection Liquiline System CA80AM Fold out the carrier board towards the front . For convenience of handling, hook the carrier board onto the locking plate. 6 x Ph2 Release the 6 screws on the electronics compartment cover using a Phillips-head screwdriver and fold out the cover towards the front.
Page 27
Liquiline System CA80AM Electrical connection Only for the "Outdoor" version Guide the cable of the heated waste hose through the cable gland indicated. Guide the power supply cable, which is provided by the customer at the installation location, through the cable gland indicated.
Page 28
Electrical connection Liquiline System CA80AM To access the electronics compartment, proceed as described in the "Routing the cables" section (→ 24). Guide the 24V connecting cable from below through the cable gland on the inner rear panel of the device and feed it up into the electronics compartment.
Page 29
Liquiline System CA80AM Electrical connection 5.2.3 "Outdoor" version: Connecting power supply and hose heater The power supply cable is not included with the delivery and must be provided by the customer. Guide the power supply cable and the cable of the hose heater from below through the cable gland on the inner rear panel of the device and feed them up into the electronics compartment (→...
Electrical connection Liquiline System CA80AM Connecting sample preparation 5.3.1 Connecting the optional cleaning valve of Liquiline System CAT810 Disconnect the mains plug. To fold out the carrier board towards the front, proceed as described in the "Routing the cables" section .
Page 31
Liquiline System CA80AM Electrical connection 5.3.2 Connecting the optional hose heater and communication between the CAT820/ CAT860 and the analyzer Only use terminated original cables where possible. The sensor cable, fieldbus cable and Ethernet cable must be shielded cables. Cable sample (does not necessarily correspond to the original cable supplied) ...
Electrical connection Liquiline System CA80AM Remove the protective cover in the upper right-hand corner. A0028925 Route the cable in the housing in such a way that the exposed cable shield fits into one of the cable clamps and the cable cores can be easily routed as far as the plug-in terminals.
Liquiline System CA80AM Electrical connection Individual types of protection permitted for this product (impermeability (IP), electrical safety, EMC interference immunity, Ex protection) can no longer be guaranteed if, for example : • Covers are left off • Different power units to the ones supplied are used •...
Operation options Liquiline System CA80AM Operation options Structure and function of the operating menu Menu/Language English Čeština Nederlands Français Deutsch Italiano Polski A0040682 A0036773 23 Display (example) 22 Display (example) Menu path and/or device designation Soft key (press function)
Page 35
Liquiline System CA80AM Commissioning CAUTION Activities while the analyzer is in operation Risk of injury and infection from medium, reagents or cleaner! ‣ Before you release any hoses, make sure that no actions, such as the pumping of sample, are currently running or are due to start shortly.
Liquiline System CA80AM Commissioning Before putting the device into operation: Connect the liquid-bearing hoses of the sample supply system. If present, connect the communication cable and hose heater of the sample preparation system to the analyzer. After mounting: Check all connections to ensure they are secure and leak-tight.
Commissioning Liquiline System CA80AM Configuring the measuring device 7.5.1 Analyzer basic setup Making basic settings Switch to the Setup/Basic setup analyzer menu. Make the following settings. Device tag: Give your device any name of your choice (max. 32 characters).