Clavia Nord Modular V3 User Manual page 128

7. Module reference: LFO group
R R R R
A A A A T T T T E E E E D D D D I I I I S S S S P P P P L L L L A A A A Y Y Y Y B B B B O O O O X X X X
The Rate display box shows the LFO rate, either in seconds/cycle or in Hz depending on current rate.
Range: 699 seconds/cycle to 392 Hz.
R R R R
A A A A T T T T E E E E
Set the frequency of the LFO, the rate, with the knob. The Output LED will show you an approximation
of the rate, while the display box will indicate the exact frequency in Hertz, or in seconds if the range is
set to Low or Sub.
R R R R
A A A A T T T T E E E E M M M M O O O O D D D D U U U U L L L L A A A A T T T T I I I I O O O O N N N N I I I I N N N N P P P P U U U U T T T T
Input for a modulation source to control the rate of the LFO. The modulation amount is attenuated by
the rotary knob next to the input.
M M M M
O O O O N N N N O O O O
Synchronizes modules in polyphonic patches to each other. This means that if you play a chord, the mod-
ule will control all voices in sync (see
of this parameter is Off.
H H H H , L , L , S , S
, L , L , S , S
I I I I O O O O U U U U B B B B
Selects one of three ranges of the LFO rate, high, low or sub. The Hi range is from 0.26 Hz to 392 Hz,
the Lo range is from 0.02 Hz to 24.4 Hz and the Sub range is from one cycle completed in 699 seconds
to one cycle completed in 5.46 seconds.
P P P P
H H H H A A A A S S S S E E E E
Sets the starting point of the LFO cycle. Range: -180 to +177 degrees. The set degree is shown in the
display box to the left of the knob.
G G G G R R R R A A A A P P P P H H H H
The graph illustrates one cycle and its phase.
KBT KBT KBT KBT
This is the keyboard tracking function. If this is set to Key, the LFO will track the keyboard with a dou-
bling of the LFO frequency for each octave. Turning clockwise from the center position will increase the
tracking, turning counter clockwise, will decrease it. Off disconnects the keyboard tracking completely.
Click on the triangle above the control to set the keyboard tracking to Key. The preset value is Off.
PW PW
PW PW
M M M M O O O O D D D D U U U U L L L L A A A A T T T T I I I I O O O O N N N N I I I I N N N N P P P P U U U U T T T T
This is a blue input for modulating the width of the pulse wave, starting at the initial width set with the
PW control. The modulation amount is determined by the rotary knob next to the input.
PW PW
PW PW
Sets the initial width of the waveform. The range is from 1% to 99%. Click on the triangle above the
knob to reset the initial pulse width to 50%. This is the preset value.
O O O O
U U U U T T T T
The LED above the output shows an approximation of the current LFO rate.
Signal: Bipolar.
Page 120
[A [A T T T T
[A [A
T T T T T T T T E E E E N N N N U U U U A A A A T T T T O O O O R R R R Y Y Y Y P P P P E E E E
"The Mono parameter" on page 44
[A [A T T T T I] I] I] I]
[A [A
T T T T T T T T E E E E N N N N U U U U A A A A T T T T O O O O R R R R Y Y Y Y P P P P E E E E
NORD MODULAR V3.0
II] II]
II] II]
for details). The preset setting