Bosch D623 User Manual page 45

Event Event
#
93 Open, Skd,
Alarm
94 Open,
RAM IV,
Alarm
95 Open, Usr,
Alarm
96 Open, KS,
Alarm
97 Point
Opening
98 Params
Changed
99 Phone
Line Fail
100 Phone
Line Rstl
101 Bad Call to
RAM IV
102 RAM IV
Access Fail
103 RAM IV
Access OK
104 Re-Boot,
Panel
105 Re-Boot
SDI
106 Output
Reset, Usr
107 Output
Reset, Skd
108 Output
Reset,
RAM IV
109 Output
Set, Usr
110 Output
Set, Skd
111 Output
Set,
RAM IV
112 Rstrl,
Tamper
113 Rstrl,
Emergency
114 Rstrl,
Panic
115 Rstrl,
Invisible
© 2003 Bosch Security Systems
Description
Opening after alarm event by sked.
Opening after alarm event by
RAM IV.
Opening after alarm event, ID reported.
Opening after alarm event by keyswitch.
Point opened by Independent Point
Control device.
Panel parameters changed.
Phone the voltage less than 3 V for
40 sec.
After Phone Line Fail event, phone line
voltage detected at greater than
3 V for 40 sec.
Panel attempted to call RAM IV but was
unsuccessful.
RAM IV attempted to connect to panel
but was unsuccessful.
RAM IV successfully connected and
disconnected from panel.
Normal start-up or reset with installer
switch.
Unexpected reset (reboot) from SDI
device.
Relay reset by user.
Relay reset by sked.
Relay reset by RAM IV.
Relay set by user.
Relay set by sked.
Relay set by RAM IV.
Restoral from alarm, Tamper point
type.
Restoral from alarm, Emergency point
type.
Restoral from alarm, Panic point type.
Restoral from alarm, Invisible point
type.
D623/D625 User Guide
Event Event Description
#
116 Rstrl, Restoral from alarm, 24-hour burglary
24-hr Burg point types.
117 Rstrl, Restoral from alarm, controlled point
Cntrl, Dly types.
118 Rstrl, Restoral from alarm, controlled point
Cntrl types.
119 Rcvr Jam Jammed condition detected on premises
RF receiver.
120 Rcvr Jam Jammed condition detected on premises
Rstl RF received cleared.
121 RF Battery Low battery detected on premises RF
Low transmitter.
122 RF Battery Low battery condition detected on
Rstl premises RF transmitter cleared.
123 RF Premises RF Transmitter Tamper
Tamper Trouble.
Trbl
124 RF Premises RF Transmitter Tamper
Tamper Restoral.
Rstl
125 SDI SDI device not responding to polling.
Missing
126 SDI SDI device declared as missing now
Missing, responding to polling.
Rstl
127 SDI Tamper open on SDI Device Tamper.
Tamper
128 SDI SDI Device Tamper restored.
Tamper,
Rstl
129 SDI Trouble detected on SDI device.
Trouble
130 SDI SDI (option bus) device trouble
Trouble, condition cleared.
Rstl
131 SDI Over Over current condition detected on SDI
Current device.
132 SDI Over current condition on SDI device
OverCur, restored.
Rstl
133 Sensor Sensor trouble detected.
Mon Trbl
134 Sensor Sensor trouble condition restored.
Mon Rstl
135 Sensor User pressed Cmd 47.
Reset
136 System System was not armed in inactive
Inactive interval. Cmd 47 or arming system
resets this trouble.
137 Test, OK No system troubles at automatic test
report time.
138 Test, Off- System trouble present at test time.
normal
Page 45
Security System
User Guide
46841D